60 20° 3 in. 14 in. 1.5 in. Prob. 4-6

Q: 15KN 25KNM 17 kN B 7m

A: To maintain equilibrium, the sum of vertical force acting on the beam is equal to zero. To…

Q: M kN-m ソー16m。 M= 1000 kN -m d: 36 ° y Find: T= Nオ kN Ax ニ A Ay: EN る の

A:

Q: 35 - In the plane truss system, the loading status of which is evident in the figure, the support…

A: Analysis of truss can be done by method of joint or method of section. The forces acting internally…

Q: A cast-iron crank has a section on the line AB of the form shown. Show how to determine the greatest…

A: Maximum value of P Px = Psinϕ Py = Pcosϕ

Q: It is obtained by fixing 4 wooden planks to each other with nails. given as a cross section. 2…

A:

Q: Determine all member forces. Using the Method of Joints. 30KN 30KN 15KN, 600 Member 1 [ Choase)…

A: Given data in question  Truss Dimensions  Point loads To find out  Member forces using Method of…

Q: 2. The force F and the dimension d are given. Because of the rollers at C, the supporting re- action…

A:

Q: Use method of the section to calculate the bar forces for the truss given below: V 24 3

A: Consider the free body diagram of the given truss as shown below.

Q: Referring to Figure Q1(a) until Figure Q1(e); (i) Check the stability and the determinacy of the…

A: "Since you have asked multiple question we will solve the first (B) for you. For other questions to…

Q: F2-28. Determine the component of projection of the force along the line OA. F = 650 N 13. 12 5 A -x…

A: Given, F= 650 N To determine, Component of projection of force F along OA

Q: The door is kept open by means of two chains. If the stresses in AE and DF are FA N and FD = 500 N,…

A:

Q: The flanged steel cantilever beam with riveted bracket is subjected to the couple and two forces…

A:

Q: 4.168 A slender, homogeneous, 20-ft rod weighing 64.4 lb is supported as shown in Figure P4.168. The…

A:

Q: Resolve each force acting on the gusset plate intoits x and y components, and express each force as…

A: Consider F1

Q: Determine the shear value when x = 5m (from the left) for the beam shown Where: P1 = 51kN; P2 = 42…

A:

Q: Find Reactions at A and D and the internal forces for all joints using method of joints.

A:

Q: Determine the forces in members AB,BC,AD &AE by method of joints .

A: Calculating the reactions first-VA+VF=86KNHF=56KNMA=0VF×12-86×8-56×7=0VF=90KNVA=-4KN

Q: Determine the moment of each force about the boltlocated at A. Take FB = 40 lb, FC = 50 lb.

A: Calculate the moment of force produced by FB about point A.

Q: Find the stresses in the wires P1, P2, P3 shown if their diameters are 100mm each and P3=20KN and…

A:

Q: a. Determine the maximum flexural stress b. If the nails shown in the cross-section can each support…

A:

Q: The 7/8-in.-diameter pins at A and C that support the structure are in single shear. Find the…

A:

Q: CW Determine the force in member BF. fa 21

A: Given truss and asked to analyse to find the force in the member BF.

Q: Consider the truss structure that l've drawn below. It is a small truss and could be part of a crane…

A: Given A simple truss,with loading, To find,force in member BE

Q: 6.

A:

Q: For the load group and influence line shown, P₁ = 8 kips, P₂ = 32 kips, P3 = 32 kips, a = 14', and b…

A:

Q: Block 4 slides in the slot in the fixed piece 1. Axis Q2 of crank 2 is fixed on 1. Q2A = 1 1/2 in,…

A: Q2A = 1.5" →Crank   AB = 4.5 →connecting rod    S = slider  5"8 →offset

Q: PROBLEM NO. 3. Given the frame shown below, Beam ABC is attached to the tensioner cable BD. Tension…

A:

Q: Determine the resultant moment of forces about the point O? Neglect the beam thickness KKN -15 m…

A:

Q: 2) The stvuct ure shown in the Figure is hinged at A and C. Find the horí gontal and vertical hinge…

A:

Q: QUESTION 4) In the frame system in figure, the diameter of pin at joint B is d. The allowable shear…

A:

Q: Determine the reactions at the fixed support A, rocker C, rocker E and pins B and D. 27.4 32.6 23.4…

A:

Q: Use the method of sections to determine the force in members CD, and GF of the truss and state if…

A: Given;

Q: F2-28. Determine the component of projection of the force along the line OA. F = 650 N 8 13. 12 5 A…

A: Given :

Q: If the 5kg block is suspended from the pulley B and the sag of the cord is d 0.15 m. Draw (FBD) and…

A:

Q: DRAW THE FBD AND JOINTS OF ALL. PROVIDE CLEAR SOLUTION. DO NOT COPY SOMEONE'S ANSWER

A:

Q: 1-7. Determine the resultant internal loading on the cross section through point D of the pliers.…

A:

Q: Determine the magnitude of the bending moment at CAssume a- 5.5 ft, b- 11.0 ft, c- 5.5 ft, w- 1130…

A:

Q: 30 mm sn

A: AB = 2m BC = 2m Shearing capacity of  each bolt = 3kN We have to find the maximum load

System of Forces

A force is an external influence or agent that changes the state of a system. According to Newton's second law, the force applied to a body is proportional to the change in momentum of a body. Hence, whenever a force is applied to a body, its momentum changes. If the body is at rest, under the action of force, its state of rest changes to motion. In other words, the magnitude of the momentum of the body changes from zero to a measurable value. Similarly, if the body possesses some initial velocity, it has some associated momentum, the effect of force can cause the body to halt or come to rest, that is, the momentum reduces to zero.