6.9. A 132 kV, 50 Hz transmission line has the following generalised constants, A = D = 0.9696 0.49° B= 52.88 74.79° ohms and C = 1177 x 10 190.15° mho. It is supplying a load of 125 MVA, 0.9 power factor lagging at 132 kV. Calculate'the sending end voltage and current. Ans. Vs = 166.1 kV, Is = 554 Amp

6.9. A 132 kV, 50 Hz transmission line has the following generalised constants, A = D = 0.9696 0.49° B= 52.88 74.79° ohms and C = 1177 x 10 190.15° mho. It is supplying a load of 125 MVA, 0.9 power factor lagging at 132 kV. Calculate'the sending end voltage and current. Ans. Vs = 166.1 kV, Is = 554 Amp

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

b) A 6052 characteristic impedance transmission line is fed by a DC source of 100V with an internal resistance of 4002. The line is 200m long and has a dielectric constant of 2.25. The load impedance is 12002. Calculate: i. The load reflection coefficient. ii. The source reflection coefficient. iii. What is the voltage at the source terminals just before AND just after 2us?
In single phase AC distribution system, the net drop is the difference of the drop in resistance due to the inphase component and in reactance due to quadrature component of current Select one: True False
Explore the potential of high-voltage direct current (HVDC) transmission systems in interconnecting regional power grids.
Q1. Transform the following vectors into spherical coordinates and then evaluate them at the indicated points. a) A = yâ, + xzâ, +4â¸ at Pi(1,–1,2) b) B = cos pâ, – sin øâ, + cos øsin pâ at P2(2, T/4,2)
If value of voltage Vs is 20kv and VR is 15 kv with load angle of 20 degrees. Value of line reactance is 5(ohm) Find value of active power and reactive power at receiving end of line.
d) Calculate the per unit voltage drop on the transmission line e) Calculate also the sending end voltage Use an overall base of 100 MVA.
Problem 1 a- Explain the meaning of the term "bundle conductor transmission line" and discuss the effects of its use on the electrical performance of a high voltage electric transmission line. b- Consider an experimental 1800 kV three phase bundle-conductor line with parameters A= 0.95 and B=j 70. Determine the value of the parameter C of the line. Assume that the line is delivering 2,000 MVA at receiving end whose voltage of 1750 kV and unity power factor. Determine the sending end voltage of the line. d- C- Determine the sending end current of the line.
Q2: The constants of a 275 KV transmission line are A = 0.8525° and B = 200275° 0/phase. Draw the circle diagram to determine the power and power angle at unity power factor that can be received if the voltage profile at each end is to be maintained at 275 KV. What type a rating of compensating equipment will be required if the load is 150 MW at unity power factor with same voltage profile. (5.5 mark)
A single circuit 60 Hz transmission line. the conductors are Linnet type with flat horizontal spacing of 17.46 feet between conductors. Determine: (a) Assume that the line is short with a length of 50 miles, calculate the parameters of the line and draw the equivalent circuit. (b) Assume that the line is average with length of 150 miles (Pi-nominal model). draw the pi-nominal circuit for the transmission line and calculate its parameters (Z and Y/2 values, where Z is the series impedance of the transmission line and Y is the shunt admittance).
If a 3-phase short circuit occurs in one of the two circuit of transmission line at point F, and the shunt impedance of the short circuit is j0.1 pu. Determine the maximum time when a short circuit can still be cleared. So=0.8+j0.3 Xd'= 0.2, XL1=XL2= 0.6, XT1=0.12, Xr2= 0.1, L1 V= 1.0 T1 L2 F T2 .XL= 0.1 Хс- 0.1. S1 S2 SL= 0.6+j0.3
Consider a simple power system: two generators (20MVA each at 13.2kV) running in parallel via a combined generator step-up transformer (rated at 30/33.3/36.7 MVA: ONAN/ONAF/ONAF cooling, 13.2 (Delta)/115 (Solidly Grounded Wye) kV). The sub-transmission line is 10.0mi long and rated at 115kV. Estimate (write the assumptions) the 3-phase bolted fault current at the end of the 115kV line.
For a 80 km transmission line given the values of R=0.5 22/km and X= 7 22/km. Find the admittance of the transmission line in per unit. Take base values as 125 MVA and tos kV.