6.43 Water (p = 1000 kg/m3) flows through a nozzle and discharges into the atmosphere at section 2. The cross section areas are A, = 250 cm? and A, = 20 cm?. The mass flow rate is 28 kg/s, h = 150 cm, and 0 = 20°. The weight of the water and the nozzle can be neglected. %3! Problem 6.43 In newtons, what are the horizontal and vertical force components (F, Fy) that are needed to hold the nozzle in place? a. -2500, 130 b. -3700, 410 c. -700, 21o d. -1200, 32o е. - 980, 140

6.43 Water (p = 1000 kg/m3) flows through a nozzle and discharges into the atmosphere at section 2. The cross section areas are A, = 250 cm? and A, = 20 cm?. The mass flow rate is 28 kg/s, h = 150 cm, and 0 = 20°. The weight of the water and the nozzle can be neglected. %3! Problem 6.43 In newtons, what are the horizontal and vertical force components (F, Fy) that are needed to hold the nozzle in place? a. -2500, 130 b. -3700, 410 c. -700, 21o d. -1200, 32o е. - 980, 140

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 4. A water flows through a pipe at a velocity 2 m/s. The pressure gauge reading is 2 bar. The datum…

Q: A reducing elbow is used to deflect water flow at a rate of 14 kg/s in a horizontal pipe upward 30°…

A: Given data:m=14 kg/s˙A1=113 cm2A2=7 cm2h=30 cm

Q: Water is flowing through a venturimeter shown. The difference in pressure between Point 1 (D = 4cm)…

Q: aining essure he U- Usirlg f SI

A: given data, pressure at A, PA= 267.7 kpa in tank A atmospheric pressure at A is 101 kpa and guage…

Q: concentrically with speed of 30 m/s. Calculate the force exerted on the plate if the jet issuing…

A: V1=V2=V=30m/s D=5cm d=2cm

Q: 3. A tank in figure C is accelerated to the right and the width of the tank is 1 m. Determine the…

Q: 12.7 The radial component of velocity of water leaving the cen- rifugal pump sketched in Fig. P12.7…

A: Given data:V2=90 ft/sVr2=45 ft/sN=3000 rpm

Q: Through the pipeline system in the figure calculate gauge and absulate presures at A and B J0. 12…

Q: Situation #2: Water flows at a rate of 20 L/s from a cylindrical tank through the pipe and nozzle…

A: Given data in question Discharge Diameter To find out Velocities

Q: The 5-kg ball A revolves at a constant speed ? in a horizontal circle as shown in Figure Q2. If ? =…

Q: m 13.111 vs at 700 m/s through a long duct in a wind tunnel, where the rature is 15° C and the…

Q: 10. A vertical storage tank with a hemispherical bottom and a cylindrical shell of 4 m inside…

Q: Assignment 4 A 16-ft- (4.8-m-) span simply supported beam, as shown in the figure below, has a clear…

A: Given:- The span of the simply supported beam = 4.8 m The clear span of the beam = 4.5 m The…

Q: A closed cylindrical tank with 0.30 m radius and 1.0 m height is fully-filled with water. The tank…

A: Given data, Radius = 0.3 m Height = 1 m Initial pressure = 15 kPa To find out the pressure at…

Q: 4. A water flows through a pipe at a velocity 2 m/s. The pressure gauge reading is 2 bar. The datum…

Q: Find the velocity (V2) and pressure (P2) at point (2)

A: Given- two cross sections of pipe 1 and 2 To find- velocity and pressure at section 2.

Q: Prob. 06: Find the rate of flow of water through a rectangular channel of 6m wide and 3m deep, when…

A: Given, A rectangular channel, Width= B = 6m Depth = y = 3m Bed slope = s= 1/2000 Chezy's constant =…

Q: 1. Determine the difference in pressure between points A and B. Use unit weights for water and oil…

Q: Find the amount of force required to hold the tube in the figure below in place. The result of the…

A: Question is based on the bent tube . Discharge through tube and pressure in pipe are given in the…

Q: ss wall at O. De

A: Diameter of cylinder (d) = 1m Length of cylinder (l) =8m Specific gravity of liquid =0.82 Density of…

Q: Q.134 The figure shows a cylinder of 4 m diameter in equilibrium. Calculate the resultant pressure…

A: The given figure consist of only water Since γw = 10 KN/m3 So, S = 1 for water ABCD part is…

Q: (Buoyancy, force on plane surface) A cube, 3.6 ft on a side, weighs 2920 lb and floats half-…

Q: Calculate the resistive force acting on the disk, with the error level not less than h4, according…

A: Given, r(m) P(kN) 0 6.34 0.05 6.28 0.1 6.06 0.15 5.72 0.2 5.1 0.25 4.78 0.3 4.37…

Q: 3.53 The water flows fully through the rectangular channel of lateral dimensions 4 m x 3 m. What is…

A: given- Rectangular channel-dimension=4 m×3 mslope S=0.0006Chezy's constant C=90

Q: A tank 50 cm in height is half-filled with oil. It is brought up by an elevator. Find the…

Q: s [p15. The velocity of the water jet discharging from the orifice can be obtained from v = V2 gh,…

Q: Q.2.A.The closed tank in figure is at (20°c) (specific weight of air =0.0118 kN/m³). If the pressure…

Q: Question- The capillary rise of water is 3cm in a tube. Find the diameter (mm) of tube if surface…

A: Capillary rise h=3 cm=0.03 m, Surface tension s=0.075 N/m, Diameter of the tube = ?

Concept explainers

Storm Sewers and Detention

The storm drains system transports rainwater or stormwater and other runoff from roads, parking lots, and roof downpipes directly to nearby creeks, rivers, or the sea without any treatment.

Question

6.43 Water (p = 1000 kg/m3) flows through a nozzle and discharges into the
atmosphere at section 2. The cross section areas are A, = 250 cm? and A, = 20
cm?. The mass flow rate is 28 kg/s, h = 150 cm, and 0 = 20°. The weight of the
water and the nozzle can be neglected.
%3!
Problem 6.43
In newtons, what are the horizontal and vertical force components (F, Fy) that
are needed to hold the nozzle in place?
a. -2500, 130
b. -3700, 410
c. -700, 21o
d. -1200, 32o
е. - 980, 140

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Q.5.b) Three pipes steadily deliver water at 20°C to a large exit pipe in Figure below. The velocity = 5 m/s, and the exit flow rate Q₁ = 120 m'/hour. Find (a) ₁: (b) Fi and (e) if it is known that increasing Q, by 20% would increase Q: by 10%. Dy = 6 cm D₂ = 5 cm D₁ = 9 cm D₁ = 4 cm
I need the answer as soon as possible
Q3: A right circular cone has the radius of the base and the height which at a given instant (to) are r =25cm and h=35 cm, respectively. If (h) is increasing at a rate of 2 cm/ sec and (r) is increasing at a rate of 1 cm/ sec. Find the rate at which the volume of the cone changes.
A 3-cm-diameter horizontal pipe attached to a surface makes a 90° turn to a vertical upward direction before the water is discharged at a velocity of 6 m/s. The horizontal section is 5 m long and the vertical section is 4 m long. Neglecting the mass of the pipe and considering the weight of the water contained in the pipe, the bending moment acting on the base of the pipe on the wall is (a) 11.9 N·m (b) 46.7 N·m (c) 127 N·m (d) 104 N·m (e) 74.8 N·m
The tank shown in the figure below is accelerated vertically down at 9.8 m/s. If the tank is 4 meters wide, find the force acting on the wall BC. A Tank is open to atmosphere Tank is open to A atmosphere t0.5 m 2 m Water В 8 m C a = 9.8m/s²
Determine the natural frequency of the system shown in the figure. The beam is of negligible mass. Given: M=25 kg, E=200 GPa, I=5x10 m4, and k spring =5 kN/m. El 4 m 11
(Buoyancy, force on plane surface) A cube, 4.4 ft on a side, weighs 3110 lb and floats half- submerged in an open tank as shown in the figure below. For a liquid depth of 10.6 ft, determine (a) the magnitude and (b) the location of the force of the liquid on the inclined section AB of the tank wall. The width of the wall is 8.1 ft. Show the magnitude, direction, and location of the force on a sketch. 10.6 ft 4.4 ft Liquid (a) FR = centerline b) YR= all from free surface Cube A V Wall width 28° lb on ft along
Water flows from 1 to 2 through curved nozzle as shown in the figure. The pressure at section 1 is 74 kPa and water flows into the atmosphere at section 2. The flow rate, Q=0.03 m³/s. Calculate the force to keep the nozzle in place. 25 cm² (2) \45° 150 cm? 40 cm Water (1)
2 A water tank is filled with Oil (SG = 0.87) to a height of 3.07 m. above the 10 mm Ø orifice which is connected at the side of the tank, how far would the water have traveled horizontally if the orifice is 4.93m. above the ground? h =3.07 m V 4.93 m 8.6 m 7.8 m O2.9 m 3.4 m X