6.3B-5. Multiple Access protocols (5). Consider the figure below, which shows the arrival of 6 messages for transmission at different multiple access wireless nodes at times t=0.1, 0.8, 1.35, 2.6, 3.9, 4.2. Each transmission requires exactly one time unit. t=0.0 1 01 U 0 3 For the CSMA/CD protocol (with collision detection), indicate which packets are successfully transmitted. You should assume that it takes .2 time units for a signal to propagate from one node to each of the other nodes. You can assume that if a packet experiences a collision or senses the channel busy and that that node will not attempt a retransmission of that packet until sometime after t=5. If a node senses a collision, it stops transmitting immediately (although it will still take .2 time units for the last transmitted bit to propagate to all other nodes). Hint: consider propagation times carefully here. Hint: consider propagation times carefully here. 4 5 23 t=1.0 U 9 t=2.0 t-3.0 t=4.0 t=5.0

6.3B-5. Multiple Access protocols (5). Consider the figure below, which shows the arrival of 6 messages for transmission at different multiple access wireless nodes at times t=0.1, 0.8, 1.35, 2.6, 3.9, 4.2. Each transmission requires exactly one time unit. t=0.0 1 01 U 0 3 For the CSMA/CD protocol (with collision detection), indicate which packets are successfully transmitted. You should assume that it takes .2 time units for a signal to propagate from one node to each of the other nodes. You can assume that if a packet experiences a collision or senses the channel busy and that that node will not attempt a retransmission of that packet until sometime after t=5. If a node senses a collision, it stops transmitting immediately (although it will still take .2 time units for the last transmitted bit to propagate to all other nodes). Hint: consider propagation times carefully here. Hint: consider propagation times carefully here. 4 5 23 t=1.0 U 9 t=2.0 t-3.0 t=4.0 t=5.0

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Related questions

Q: Suppose dprop is greater than dtrans. At time t=dtrans, where is the first bit of the packet?

A: The answer is

Q: . Suppose A is connected to B via an intermediate router R, as in the previous problem. The A-R link…

Q: Consider a network with 4 links between two hosts where the maximum allowable packet size is 1000…

A: Answers:- 1st method:- To calculate the total time it takes to send 6000 bits from one host to…

Q: Consider this multihpop network running the 802.11 MAC protocol in ad-hoc mode (RTS-CTS-DATA-ACK)…

A: ANSWER:-

Q: The RDT 3.0 protocol (b). Consider the rdt3.0 sender and receiver shown below, with FSM…

A: Transition t1: This transition happens after the receiver has processed the first packet and sends…

Q: This elementary problem begins to explore propagation delay and transmission delay, two central…

A: let's break down the concepts of propagation delay, transmission time, and end-to-end delay in the…

Q: 6.3-3. Multiple Access protocols (c). Consider the figure below, which shows the arrival of 6…

A: Slotted ALOHA works in time slots, where the time for a slot is the time to transmit a single…

Q: Computing Packet Transmission Delay. Suppose a packet is L = 3000 bytes long (one byte = 8 bits),…

A: Transmission delay is a key concept in data communication, representing the time it takes to push…

Q: e sender and receiver can be reordered, then rdt3.0 will not w he diagram, clearly explain why this…

Q: Consider a packet of length L that begins at end system A and travels over three links to a…

A: The above question is solved in step 2 :-

Question

6.3B-5. Multiple Access protocols (5). Consider the figure below, which shows the arrival of 6
messages for transmission at different multiple access wireless nodes at times t=0.1, 0.8, 1.35, 2.6,
3.9, 4.2. Each transmission requires exactly one time unit.
t=0.0
n
[
2
3
t=1.0
4
t=2.0
4
For the CSMA/CD protocol (with collision detection), indicate which packets are successfully
transmitted. You should assume that it takes .2 time units for a signal to propagate from one node to
each of the other nodes. You can assume that if a packet experiences a collision or senses the
channel busy and that that node will not attempt a retransmission of that packet until sometime
after t=5. If a node senses a collision, it stops transmitting immediately (although it will still take .2
time units for the last transmitted bit to propagate to all other nodes). Hint: consider propagation
times carefully here. Hint: consider propagation times carefully here.
t=3.0
5 6
t=4.0
t=5.0

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Define CSMA/CD

VIEW

Step 2: Transmission Analysis

VIEW

Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, computer-science and related others by exploring similar questions and additional content below.

Similar questions

please look at the two pics and answer please
Alert dont submit AI generated answer.
Suppose A is connected to B via an intermediate router R, as in the previous problem. The A-R link is instantaneous, but the R–B link transmits only one packet each second, one at a time (so two packets take 2 seconds). Assume A sends to B using the sliding window protocol with SWS = 4. For Time = 0, 1, 2, 3, 4, state what packets arrive at and are sent from A and B. How large does the queue at R grow?
Given what we know about transmission delay and the following: A web client and a web server separated by one intermediary router. • Each link carries data at 1Mbps with an MTU of 8192 bytes • Each link is 1000 km long with a propagation speed of 250000 km/s • Zero processing and queueing delays • Connection management packets (packets used for opening a connection, confirming a connection and acknowledging receipt of information) contain no data and all packets have 125 bytes of overhead on top of any data they may contain. • The web client makes an HTTP request to the server that is 250 bytes long. • The requested data is 4 kilobytes in size with 500 bytes of overhead for the HTTP status and headers What is the RTT to open the connection? а. b. How long would it take for a web client to complete the request? You can ignore any time needed to close the connection.
Consider a reliable data transfer protocol that uses only negative acknowledgements (NAKS). (a) Suppose the sender sends data only infrequently. Would a NAK-only protocol be prefer- able to a protocol that uses ACKS? Explain. (b) Now suppose the sender has a lot of data to send and the end-to-end connection expe- riences few losses. In this case, would a NAK-only protocol be preferable to a protocol that uses ACKS? Explain.
Suppose A is connected to B via an intermediate router R, as in the previous problem. The A-R link is instantaneous, but the R–B link transmits only one packet each second, one at a time (so two packets take 2 seconds). Assume A sends to B using the sliding window protocol with SWS = 4. For Time = 0, 1, 2, 3, 4, state what packets arrive at and are sent from A and B. How large does the queue at R grow?
Which one of the following statements is FALSE? File Transfer Protocol (FTP) is a TCP service that operates on ports 20 and 21. Telnet is a TCP service that operates on port 23. Simple Network Management Protocol (SNMP) is a TCP service that operates on port 25. Dynamic Host Configuration Protocol (DHCP) is a TCP service that operates on port 80.