6. Write down the lift curve equation (lift coefficient versus angle of attack) according to the thin airfoil theory. What is the amount of the lift curve slope for a thin airfoil ? NACA 2412 airfoil LEg. (4.57) * 2.0 1.6 1.2 Lift coefficient 0.8 0.4 -0.4 Eg. (4,64) --0.1 Moment coefficient -0.8- -1.2 -0.3 • Re -3.1 X 10 O Re -8.9 X 10 L-0.4 -8 16 24 a, degrees dc =? da

6. Write down the lift curve equation (lift coefficient versus angle of attack) according to the thin airfoil theory. What is the amount of the lift curve slope for a thin airfoil ? NACA 2412 airfoil LEg. (4.57) * 2.0 1.6 1.2 Lift coefficient 0.8 0.4 -0.4 Eg. (4,64) --0.1 Moment coefficient -0.8- -1.2 -0.3 • Re -3.1 X 10 O Re -8.9 X 10 L-0.4 -8 16 24 a, degrees dc =? da

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The drag polar for the ASW 27B high performance sailplane is: CD = 0.01 +0.02CL2. What is its maximum lift-to-drag (L/D) ratio? 18 25 35 70
- Study how the lift and drag varies with a change in angle of attack for a flat plate, symmetrical airfoil and asymmetrical airfoil when Re is below 50'000 and compare it to higher Re.
Discuss and comment on the effect of drag polar for Re 5003352.
Consider a rectangular wing with NACA 0009 airfoil section spanning the test section of a wind tunnel, the test section airflow conditions are standard sea level w/a velocity of 116 mi/hr. The wing is at an angle attack of 4° and the wind tunnel force balance measures a lift of 28.43 lbf. What is the area of the wing? R.N = 3.0 X106; C̟ at angle attack of 4° = 0.4 %3D
A Mitsubishi A6M Zero which has a wing area of 22.44 square meters with a lift generated of 6,000 N. If the wingspan is 12 meters, Calculate the velocity at minimum thrust required at standard sea level conditions. Assume wing is an elliptical planform and parasite drag is 0.045.
You are designing an airfoil for a new hobby RC plane. Because of your limited knowledge, you have mistakenly approximated your airfoil as an ellipse with a = 75mm and b = 12mm. Here, “a” is the depth of your wing and “b” is the thickness. Your plane travels through the air at approximately 20mph (8.9m/s). As it does so, skin friction produces a drag-induced heat of 800W on your wind, of length 1m. Properties of Air: k = 0.025 W/mK, Pr = 0.72, v = 1.847 x 10−5, u = 16.84 x 10−6, p = 1.2 kg/m3, B = 1/Tf (ideal gas), TInfinity = 25oC a) What is the Reynold’s number? Hint: “D” is taken to be the thickness for an elliptical crosssection. b) What is the Nusselt number? c) What is the convection coefficient? d) What is the average temperature of your wing? Assume an ellipse perimeter of approximately 200mm.
An aircraft has the drag polar, C_d=0.015+0.05C_l^2 For a lift coefficient of 0.5, find the value of the drag coefficient and lift drag ratio? I am asking It For Second Time. Please Read the Question Carefully.
Assume the stabilizer of an airplane is a flat plate. If the transition /critical RN 750,000, what is the skin-friction drag of a rectangular stabilizer having a span of 1.73 m and a chord of 0.81 m at a speed of 44.7 meters per second? Assume standard sea level conditions.-round off to 4 decimal places-show complete solution
A conventional low speed aircraft had the following aerodynamic characteristics: CDo=0.020. e=1.0 (Oswald efficiency). The aircraft was flown to maintain a steady level flight and for minimum thrust required, at a lift coefficient of Cz=0.8. The numerical value of the aspect ratio of the wing is three decimal places). (in
Calculate the Road load power for the case Toyota Prius (fronatal area =0.8m2 sliding over a street has coefficient of rolling resistance CR= 0.015, drag coefficient CD=0.26 air density=1.2 kg/m3 the mass of the car 1500 kg. O a. 3.48 kW O b. 2.15 kW O . 9.72 kW
The NACA 4412 airfoil has a mean chamber line given by 0.25 for 0ss0.4 l0.111 02+ 08: - ()'| 0.111 0.2 + 0.8 – (4)*| for 0.4 ss1 Using thin airfoil theory, calculate Cme/4 and Xcp/C when a =3° %3D NIU