6. Water flows from a nozzle with a speed of V= 10 m/s and is collected in a container that moves toward the nozzle with a speed of Vev= 4 m/s as shown in the figure below. The moving control surface consists of the inner surface of the container. The system consists of the water in the container at time t=0 and the water between the nozzle and the tank in the constant diameter stream at -0. At time -0.1 s what volume of the system remains outside of the control volume? How much water has entered the control volume during this time period? Repeat the problem for 1-0.3 s. Stream diameter = 0.1 m Nozzle V = 10 m/s V = 4 m/s -3 m Container at r = 0 Stream at r = 0 Moving control volume

6. Water flows from a nozzle with a speed of V= 10 m/s and is collected in a container that moves toward the nozzle with a speed of Vev= 4 m/s as shown in the figure below. The moving control surface consists of the inner surface of the container. The system consists of the water in the container at time t=0 and the water between the nozzle and the tank in the constant diameter stream at -0. At time -0.1 s what volume of the system remains outside of the control volume? How much water has entered the control volume during this time period? Repeat the problem for 1-0.3 s. Stream diameter = 0.1 m Nozzle V = 10 m/s V = 4 m/s -3 m Container at r = 0 Stream at r = 0 Moving control volume

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Two gases enter a combining tube and leave as a single mixture. . For the first gas, A₁=72in² V₁=205m/s V₁=120gal/lbm . For the other gas, A₂=48in² m2=20lbm/s P2=2kgm/m³ ● . At the exit, V3=320ft/s V2=9ft³/lbm Find the (a) velocity at section 2 in m/s, (b) mass flow rate at the exit section in kgm/s, and (c) area at the exit section in m².
A uniform cross-sectional water tank is placed in a cart as shown in figure. The cart is mounted on frictionless rollers and the water is discharged to atmosphere through an attached nozzle. However, the the water level the tank is maintained at a constant height h above the nozzle by an external supply at a volumetric flow rate Q. The cart is restrained from moving by the cable seen in figure . The mass of the tank, cart and water is M. In terms of the parameters h, Aj and the water density ρρ. derive expressions for (a) the volumetric flow rate Q and (b) the tensile force T in the cable. (c) At time t = 0, the cable is cut, and the cart begins to move to the left at a velocity Vc{t} that increases with time. Derive an expression for Vc{t}.
An incompressible fluid flows steadily through two pipes of diameter 0.15 m and 0.2 m which combine to discharge in a pipe of 0.3 diameter. If the average velocities in the 0.15 m and 0.2 m diameter pipes are 2 m/s and 3 m/s respectively, then find the average velocity in the 0.3 m diameter pipe.
Problem Consider a cylindrical pipe of length L and diameter D = 2R. The angle that the axis of the pipe forms with the vertical direction is a. Assume that when the fluid enters the pipe its velocity is uniform (i.e., it has the same value over the entire cross-section of the pipe) and equal to U in the axial direction. In the radial and angular directions, the velocity is zero. So, it is: 2 =0: v(r, 0, 2) = Ue, (1.1) Here v is the fluid velocity and e, is a vector of unit magnitude parallel to the coordinate axis z; furthermore, we have assumed that the pipe inlet is located at z = 0. Near the entrance of the pipe, the velocity profile varies in the axial direction. But after a certain entrance length, the profile becomes fully developed, no longer changing with z. The evolution of the velocity profile is sketched in Fig. 1, where, for clarity, the pipe inclination is not shown. The entrance length is denoted by L.. For z > L., the fluid velocity is no longer a function of the axial…
3. A pipe with varying cross-sectional areas is set up vertically as shown in the drawing. Water enters the pipe from the top wider end at a speed of 300 cm/s. Calculate (a) the mass flow rate of water (the amount of mass entering/exiting the piper every second) and (b) the water pressure at the bottom narrower end section of the piper. (Density of water is p = 1000 kg/m2 1.00 g/cm')) P 1.20x10 Pa 10.0 cm h=4.00 m 2.50 cm2 P= ?
3. Air is flowing down a circular duct as shown in the figure. At station 1 the velocity is V₁ and the duct diameter is D₁. The duct gradually enlarges to station 2, where the air exits to the atmosphere, and the diameter is D₂. A conical centerbody with a cone angle of 30° is inserted into the duct exit. The diameter of the cone base is d. You may assume that the velocity is low enough that p = constant. control surface V₂ 1 0 = 30° V₂ F Figure for problem 3. (a) Find an expression for the gauge pressure at station 1 in terms of V₁, D₁, D₂, d, e, and p. What assumptions do you have to make to solve this problem? (b) What is the force, F, required to hold the cone in place? You may ignore the weight of the cone. Use the following values: V₁ = 20 m/s, D₁ = 30 cm, D₂ = 60 cm, and d = 58 cm. You may assume that the air density is at standard conditions, p = 1.225 kg/m².
2. In the system shown in figure below, a pump draws a solution of water from a storage tank through a pipe with cross sectional area 0.05ft². The velocity in the suction line is 3 ft/s (0.914 m/s). The pump discharges through a pipe with cross sectional area 0.02 ft² to an overhead tank. The end of the discharge pipe is 50 ft (15.2 m) above the level of the solution in the feed tank. Friction losses in the entire piping system are 10 ft. lbf / lb (29.9 J/Kg). What is the work done by the pump per unit mass of water? (25%) A = 0.02 50 ft A = 0.05ft² Pump 2 ft² a b
Water flows through a pipe AB of diameter d1= 60mm, which is in series with a pipe BC of diameter d2= 85mm in which the mean velocity V2 = 3m/s. At C the pipe forks and one branch CD is of diameter d3 such that the mean velocity V3 is 2.5 m/s. The other branch CE is of diameter d4= 40mm and conditions are such that the discharge Q2 from BC divides so that Q4= ½ Q3. Determine Q1, Q3, Q4 and d3.
A water source generates a flow rate of 30 m 3/s in a region of y= 0 with angle zero degree and x=0 with an angle of 90 degree. Determine the magnitude of water velocity V at r= 5 m ( Use pi number =3 and water density =1000 kg/m3)ANSWER: V= 4 m/s
Methane in the gaseous state flows at a rate of 0.072 m^3/s in a pipe at a temperature of 27°C and gauge pressure of 148.675kPa (point 1). The pipe is divided into two branches (point 2 and 3), as seen in the figure. If the exit velocity in pipe 3 is 12 m/s with a density of 1.9 kg/m^3, what is the flow rate and velocity in pipe 2? Consider that in section 2 the fluid is leaving with a temperature of 402°C and an absolute pressure of 175 kPa. We have an atmospheric pressure of 101.325 kPa and R_methane = 0.5182 kJ/kg ⚫K. (1) Inflow D1 D3=50mm D2=100mm (3) (2)
The water enters the sprinkler nozzles with a flow rate of 50 liters / hour in the vertical axis direction and leaves the sprinkler nozzles as 25mm diameter jets and making θ angle with the tangential direction as shown in the figure. The length of the sprinkler arms is 0.45 m. Without considering friction effects; For θ = 75 °, set the rotational speed in rpm.