6. Water enters a hydraulic turbine through a 25-cm diameter pipe at a rate of 0.6 m³/s and exits through a 30-cm diameter pipe. The pressure drop in the turbine is measured by a mercury manometer to be 1.3 m. For a combined turbine-generator efficiency of 80 percent, determine (a) the net electric power. output. (b) and pressure difference across the turbine. Disregard the effect of the kinetic energy correction factors.

6. Water enters a hydraulic turbine through a 25-cm diameter pipe at a rate of 0.6 m³/s and exits through a 30-cm diameter pipe. The pressure drop in the turbine is measured by a mercury manometer to be 1.3 m. For a combined turbine-generator efficiency of 80 percent, determine (a) the net electric power. output. (b) and pressure difference across the turbine. Disregard the effect of the kinetic energy correction factors.

Name: 6. Water enters a hydraulic turbine through a 25-cmdiameter pipe at a
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: 6. Water enters a hydraulic turbine through a 25-cmdiameter pipe at a rate of 0.6 m³/s and exits througha 30-cm diameter pipe. The pressure drop in theturbine is measured by a mercury manometer to be1.3 m. For a combined turbine-generator efficiency

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Water flowing at 0.5 m3/min enters the turbine of a micro-hydroelectric generator and delivers a shaft work of W= 2,500 J/kg. What is the power delivered by the generator if it works at 95% efficiency, n = 0.95?
Water is pumped from a lower chamber to a higher chamber by a pump driven by a 55 kW electric motor with an efficiency of 85%. The free surface of the upper chamber (open surface to the atmosphere) is 75 m higher than the free surface of the chamber below. The free surface velocities are negligible. The magnitude of the gravitational acceleration is given as 9.81 m/s^2. Since the mass flow rate of the water is 50 kg/s, calculate the mechanical power loss in kW during the upward transfer of the water. 1.665 9.96 18.21 3.21 12,45 5.70
From a PPRC (shiny surface) pipe with an inner diameter of 20.5 mm and a length of 70 cm, water at 20 ° C flows at a flow rate of 1500 L / h and a pressure difference of 52 mbar occurs. Based on these data, find the speed of the water, the Re number, the friction factor, the f value and the pressure difference (in mbar) and show the f value you found from the Moody diagram. (For 20 ° C water; p = 998 kg / m3,µ= 1.003x10-3 N.s / m2, v = 1.005x10-6 m2 / s, 1 bar = 10.2141mSS)
A pump operates at 78% efficiency when it is pumping water (density = 1000 kg/m³) at a volume flow rate of 0.3 m³/s with a head of 17 m. The gravitational acceleration g = 9.81 m/s². The pump impeller's shaft power is kW.
6.5-7
A fluid flowing in a pipe 1000 ft above the reference line at a pressure of 200 psia, specific volume of 2 ft3 /lb, velocity of 200 ft/sec and internal energy of 100 Btu/lbm. Determine (a) the total energy of the flowing fluid with respect to the reference line and (b) the specific enthalpy in Btu/lbm . Local gravity is 32 ft/sec2 .
2. A fan delivers 283.2 m³ / min of air with a density of 1.2 kg/m³ through a duct 5.08 cm by 5.08 cm at the static pressure of 2.3 cm WG. If the power input to the fan is measured as 2.70 kW, determine; (a) the air velocity, m/sec (b) the total head if the velocity head is 8.2 meters (c) the mechanical efficiency of the fan.
A Liquid fluid with a density of 1,750 kg/m3 from an elevated 2m open reservoir (P1=0 bars) flows before the pump at 7.5 m/s. The liquid fluid is pumped at an unknown final velocity to a 75 meter elevated tank with a pressure reading of 7.75 Bars. assuming Friction losses is 757.75J and the actual WORK of the pump is 1,933,400J. Calculate the power in HP if the pump's efficiency is just 75% and for every 1,000 kg of fluid per hour.
In rural housing the water source is obtained through groundwater pumped upwards. Suppose the groundwater source has a depth of 60 m from the surface. The water will be lifted as far as 5 m above ground level with a pump. The diameter of the pipe inlet is 10 cm and the outlet is 15 cm.By ignoring the interaction of heat with the environment and heat due to friction, determine the input work (Watt) required by the pump for the water to flow stable at a rate of 15 liters / s. (Water type mass 1000 kg / m ^ 3). (Application of the 1st Law of Thermodynamics to open systems)
The capacity of a certain pump is 5251 gallons per hour with a capacity of 68.54%. A city uses this pump to extract water from a water supply from a body of water where in the intake is 10.2 ft below the surface of the body of water. A 3-in S40 is used to transfer the water through a pipe with a total length of 8848 ft having a total friction loss of 222.7 (ft-lbf)/lbm. Given that the cost electrical power is 14.7 cents/kWh, what is the hourly pumping cost in cents per hour? Note that in this problem, the inlet to the pump is 35.7 ft above the surface of the body of water while the water level in the tank discharge is always 380 ft above the pump discharge Answer options: 700 557 1175 685 226
Q1: The pump shown in Fig. P8.75 delivers a head of (hp) 250 m to the water. Determine the power that the pump adds to the water. The difference in elevation of the two ponds is 200 m.