6. Question 6 (a) Give the expression that relates the overall gain of an Operational amplifier, the differential gain Ad, and the common mode gain, Acm with the voltages at its inputs, v. and v.. (b) Define CMRR (Common Mode Rejection Ratio), in dB scale. (c) If CMRR is 100 dB and the common mode gain is Acm=0.5, what is the differential gain Ad?

6. Question 6 (a) Give the expression that relates the overall gain of an Operational amplifier, the differential gain Ad, and the common mode gain, Acm with the voltages at its inputs, v. and v.. (b) Define CMRR (Common Mode Rejection Ratio), in dB scale. (c) If CMRR is 100 dB and the common mode gain is Acm=0.5, what is the differential gain Ad?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Outline the main features of a non-inverting operational amplifier
EXPLAIN COMMON DRAIN, MULTISTAGE ( NEED ONLY HANDWRITTEN SOLUTION PLEASE OTHERWISE DOWNVOTE).
4. Is it possible to get a gain less than unity using a non-inverting amplifier configuration? If yes, sketch a circuit.
Subject: ELECTRONICS 2
Given in the figure is a two-stage amplifier design that employs negative feedback. Answer the following questions. Use the notation (R1 + R2 + ... + Rn) for series resistors and (R1 || R2 || ... || Rn) for parallel resistors for clarity and ease. Assume that the transistors are already biased properly in the saturation region and ro1 = ro2 → ∞. Also assume that the capacitors have infinite capacitance. 1.) Find the expression for the open loop gain Av 2.) Derive the resistance Rin which is the resistance that can be seen at the input port of the amplifier
Consider the following statement: In feedback amplifiers, concerning the connections between the direct amplifiers and the feedbacks network, a shunt connectiın at the input part servers to set an increased versiın of the input impedance of the direct amplifier, whereas again a shunt connection at the output part services to set a decreased version of the output imdepance of direct amplifier. Explain what is wrong with the statement above by drawing representative circuit diagrams and outlining the necessary calculations.
What is mean by operational amplifier? Derive the input/output relationship in inverting and non-inverting amplifier.
Design a unity gain inverting summing amplifier that will output the sum of two input voltages. Use a feedback resistor of 2.5kQ.
a) What is the input impedance of an inverting amplifier circuit? What is the input impedance of a non-inverting amplifier circuit? b) What is the formula for the gain of an inverting operational amplifier circuit with input resistor Ri and feedback resistor Rf? Draw the circuit. c) What is the formula for the gain of a non-inverting operational amplifier circuit with input resistor Ri and feedback resistor Rf? Draw the circuit.
Three amplifiers/ attenuators with voltage gains (ratios) 40, 0.8 and 5 are cascaded. Input voltage to the first stage is 500 uV. a. Find the overall (total) gain in ratio and in dB. b. Find the individual (each stage) gain/ attenuation in dB. c. Find the output voltages of each stage.
Figure 6 shows a circuit where feedback is provided between the drain and gate of the transistor M1 Q6 Draw the small signal equivalent circuit of the open loop circuit obtained by breaking the loop at the gate of transistor M1 (suitable for the analysis in the mid band frequency range). Consider Cg as short circuit in the model and state any assumption. (a) (b) State the necessary conditions for the oscillation to occur in the circuit. Using the conditions from (b), derive an expression for the amplifier oscillation frequency fo. (c) Derive the necessary condition for the oscillation to occur in the circuit and state if you can conclude that the circuit will oscillate when considering the values of the inductances L2 = 8 LI = 2 mH; capacitors C = 2 nF; transconductance of the transistor gml = 1.4 mS; and resistors R1 = R2 = Rs : 10 k2. (d) %3D L2 L, R, Cg. C Vout Cp M1 R2 CG Rs Cs Vss = 0 V Figure 6
Şe s deve e R yuk utrerncinin ak reguamekteor. M. deyamua kalacak şekinos ie maksimum dečerini hesapie The current of a load resistance Rp is regulated with the feedback circuit shown in the figure. The Mosfet operates in saturation. What is the maximum value of Rp while M, remains in saturation? Circuit parameters / Bevre Perametreleri VREF=2.8 V, Rs=100 , w/L=54/0.18, VoD = 41 V, H,Cox = 200 µA?, VTH = 0.4 V, A = 0, A, = 00. VDD I. * RD A1 VREF Rs O a. 15.96 k O b. 23.94 k O c. 18.62 kn O d. 13.30 kn O e. 7.31 ko O f. 21.28 kO O g. 9.97 kn O h. 4.65 kn WH.