6. I) Precipitation hardening II) Solid solution alloying III) Reducing the grain size IV) Creating a texture by producing a grain structure with a preferred orientation. Which of the metallurgical or processing technique(s) given above can be applied to improve the creep resistance of metal alloys? a) I, II, IV b) I, II, II c) Only III d) II and IV e) All of them

6. I) Precipitation hardening II) Solid solution alloying III) Reducing the grain size IV) Creating a texture by producing a grain structure with a preferred orientation. Which of the metallurgical or processing technique(s) given above can be applied to improve the creep resistance of metal alloys? a) I, II, IV b) I, II, II c) Only III d) II and IV e) All of them

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

You are given three metal test samples, with the same chemical composition and differing grain sizes: A: 5.0, B: 10.0 and C: 20.0 microns. Samples A and B have been tested and have yield stresses of 142.4 MPa and 135.8 MPa (all numbers are rounded off to the 1st decimal point). Based on this information, which of the following values do you think will be the closest to the yield stress of Sample C? In calculating the answer, use the Hall-Petch relation between yield stress of a metal o vield and the grain size of the metal d, which is Oyield = 00 + kd¬1/2 where k and og are constants. (This question has only one correct answer) а. 100.6 MPa b. 131.1 MPa С. 152.4 MPa O d. 115.8 MPa е. 128.1 MPa
8
Question 1 Aluminium alloys find use in aircraft industry because of A) good weldability B low specific gravity C) good corrosion resistance D high strength
a) What is the final length of a 2 m long bar of copper, 0.01 m in diameter, stressed by a 500 kg force? (Ecu = 128 GPa). b) If a steel bar of the same diameter has the same force applied to it, how long must it be to extend the same amount as the copper bar in part (a)? c) For an ASTM grain size of 6, approximately how many grains would there be per square inch under each of the following conditions? (i) At a magnification of 100X (ii) Without any magnification
Draw Time-Temperature-Transformation (T.T.T) diagram and show the design of cooling curve to obtain following microstructures: i) 100% Coarse Pearlite ii) 75% fine Pearlite +25% Austenite iii) 50% upper bainite +50% Martensite
Measured vs. Theoretical Density A rectangular piece of molybdenum with dimensions 1cm x 2cm x 4cm is placed on a mass balance and is found to have a mass of 81.857 g. a) Use this data to calculate the density of the sample. b) Use atomic and crystal structure data obtained from Wikipedia to calculate the theoretical density of molybdenum. c) Offer a brief explanation as to why these two values might be different.
4.The following diagram shows the structure of material after fracture into two parts. Which of the following represent completely ductile material? a) b)
Q3 (3 : Multiple Choice D weaker 4) The pearlite microstructure is formed a) in hypereutectoid steels c) in eutectoid steels d) all of the above b) in hypoeutectoid steels e) none of the above 5) Within the elastic limit a) Strain is produced by bond breaking and reforming b) Stress is proportional to strain c) Complete recovery of strain is not possible d) Strain is produced by bond stretching e) b and d, are correct f) a and b, are correct 6) Boron can diffuse in silicon can by either a vacancy or interstitial mechanism. Which statement is probably true? a) Dim
Which is/are used for annealing ferrous alloys? Check the right answersa) spheroidizing b) normalizing c) full annealing d) precipitation hardening e) none of the above
O Which alloy type would you recommend for a dental implant? a) Aluminum alloy b) Magnesium alloy c) Copper alloy d) Titanium alloy e) Nickel alloy
The properties of a titanium allow used in commercial airplanes are shown in the table: Strength (MPa) Grain Size (mm) 0.020 162 0.055 148 Determine a) the constants of the Hall-Petch equation and b) the grain size required to obtain a strength of 192 MPa
None