6. Determine the maximum compressive and tensile forces, in kN, developed in members PG, QP, GH, and VG of the Baltimore truss shown below due to the load induced by the trailer truck shown below (convert everything in SI units, 1Tonne = 908 kg). TSRQP BCDEFGHI -12 @25 ft = 300 ft 1.ST 2.5T 2.5T 3.5T 3.5T 3.5T 6.0m 1.5m 8.2 m 1.5m 1.5m 25 ft M 25 ft

6. Determine the maximum compressive and tensile forces, in kN, developed in members PG, QP, GH, and VG of the Baltimore truss shown below due to the load induced by the trailer truck shown below (convert everything in SI units, 1Tonne = 908 kg). TSRQP BCDEFGHI -12 @25 ft = 300 ft 1.ST 2.5T 2.5T 3.5T 3.5T 3.5T 6.0m 1.5m 8.2 m 1.5m 1.5m 25 ft M 25 ft

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

B7
Consider the truss shown in (Egure 1). Suppose that F-60 kN and F₂-25 kN Figure 40 KN Part C Fau 50 AN Submit -2m- D 15m 1of1 > 15m 15m μA Value -F₂ Part A Request Answer Determine the force in member ED of the truss, and state if the member is in tension or compression Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. HA FED Value Submit Part B Request A Determine the force in member EH of the truss, and state if the member is in tension or compression Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. Submit Fon- Value Determine the force in member GH of the truss, and state if the member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of…
4
load 1: 60 load 2: 50
For the truss and loading shown, determine most economical cross-sectional area (in in2) of member DF, if P = 40453 lb, Q = 38513 Ib, y = 7.94 ft, and the stress in the member is 12.47 ksi . Round off the final answer to two decimal places. M 0004(1).png ... В E 4 panels at 10 ft = 40 ft
Please round off the final answer to 3 decimals.
Consider the simply supported truss as defined in the figure and parameter table. Find the force in members CD, HD, and HG. Follow the convention the tension is positive and compression is negative. A 1910 P. B cc 000 BY NỌ SA 2021 Cathy Zupke L₂ parameter value L₁ 1.5 L2 1.5 L3 2.5 LA 2 1.5 1.5 30 50 60 60 L5 L6 P₁ P₂ P3 P₁ units H # G P₁ E F The force in member CD = The force in member HD = The force in member HG = m m EEEEEZZ m m m L3 KN KN ↑ KN KN KN 3
Please help me
Determine the smallest safe cross-sectional areas of members CD, Cl and CH for the truss shown. The allowable stress are 100 MPa in tension and 80 MPa in compression. Indicate tension or compression. (Draw the required FBD and answer in mm2). Fa a –– a→– a- B D |E A a F G H а 3 2 т 45 kN
SITUATION 1 Determine (approximately) the force in each member of the truss. Assume the diagonals can support either a tensile or a compressíve force and assuming that the díagonals cannot support a compressíve force. A. Use Method 2 7 k 14 k 14 k 7 k Н F E oo 2 k 380 6 ft A D В C 8 ft 8 ft 8 ft B. Use Method 1 50 kN 40 kN 20 kN E D 3 m B 3 m 3 m
ANSWER IN 3 DECIMAL PLACES
The bars of the truss each have a cross-sectional area of 800 square mm. Determine the average normal stress in members BC, BG, and BH. State whether the stress is tension or compression.