6. A transmission line has a span of 150 m between level supports. The conductor has a cross-sectional area of 2 cm². The ultimate strength is 5000 kg/cm². The specific gravity of the material is 8-9 gm/cm³. If the wind pressure is 1-5 kg/m length of the conductor, calculate the sag if factor of safety is 5. [3-5 m]

6. A transmission line has a span of 150 m between level supports. The conductor has a cross-sectional area of 2 cm². The ultimate strength is 5000 kg/cm². The specific gravity of the material is 8-9 gm/cm³. If the wind pressure is 1-5 kg/m length of the conductor, calculate the sag if factor of safety is 5. [3-5 m]

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

RMS VALUE OF MAXIMUM AND MINIMUM STRESSES IN INSULATION OF SINGLE CORE CABLE Emax=50kV/cm AND Emin=15kV/cm. CONDUCTOR DIAMETER IS 1.8cm, CALCULATE THE POTENTIAL OF THE CABLE.
The Cost OF Single phase overhead feeder is OMR q Per KM(a is area of cross section in sq mm) and the intrest and depre Ciation Chargs onfeeder omical carrent density are 7Y. defermain to use for the most econor requiring Full load current of 27% of the 12 baisa is year. The Cost per unit ass ume resistance of Im lenahth length and I mm² secfion of Conductor as 1/32 find Current densi ty =?
In an overhead transmission line, if 'L' is the length of span in meters, 'w' is the weight of conductor per meter, and 'T' is the allowable tension in the conductor in kg, then the sag 'S; in meters is given as (a) wL²/8T (c) WL³/8T (b) WL²/4T (d) WL4/8T
A single core cable is to be used for 66 kV to earth. Its conductor diameter is 2 cm and its three insulating materials have permittivity 5, 4 and 3 respectively. The corresponding safe maximum stresses are 38 kV/cm, 26 kV/cm and 20 kV/cm, respectively. Find the minimum diameter of the sheath.
33 kv single core cable has a radius of conductor of 0.6 cm. The insulation martial has two layers. The thickness of the first and second layers are 0.8 cm and 0.4 cm respectively. The relative permittivity of the first and second layers are 4 and 3 respectively. Find 1- The minimum electric stress of the cable. 2- The maximum electric stress of the second layer. 3- The minimum electric stress of the second layer. 4- The minimum electric stress of the first layer.
Q1: A 1-ph, 220 V, 50 Hz overhead line has a distance of 4 m between its .conductors and 7 m above the ground. The diameter of each conductor is 15 mm The capacitance between conductors (in pF) for a length of 50 km .2 *.----- without the effect of ground is (2) uhi هذا السؤال مطلوب The capacitance between conductors (in uF) for a length of 50 km with .1 * .----- the effect of ground is (2) Jahi هذا السؤال مطلوب (2) Jihi * The charging current (in Ampere) without the effect of ground is .3
The cost of a single phase overhead feeder is OMR 17 a per km (a is area of cross section in sq mm) and the interest and depreciation charges on feeder are 7%. Determine the most economical current density to use for distribution requiring full load current of 70% of the year. The cost of generating electrical energy is 12 baisa per unit. Assume resistance of 1 m length and 1 mm section of conductor as 1/62 ohm. Current density =- A/mm?
Q1. Transmission and distribution lines are important components of any power system study. (A) In relation to high voltage overhead ac transmission lines, Discuss the choice of materials for the conductors in terms of their electrical/mechanical properties and the costs involved. Discuss the factors that determine the distance (D) between phase conductors and explain the impact of the distance D on the inductance and capacitance values of the line at different voltage levels. Support your arguments with relevant equations where appropriate. Discuss the impact of the radius of the conductors on phase capacitance and inductance values and why bundles are used at very high voltages.
Write any four methods of voltage control and Draw the basic block diagram of AC – DC transmission system. and A transmission line has a span of length 250 m and the weight of the conductor per metrelength is 0.63 Kg. The tension in the conductor is 1250 Kg. Calculate the sag and heightabove the ground at which the conductor should be supported. Consider the groundclearance required is 13m