6. A parallel circuit of 25 - ohm resistor, 64 – mH inductor and 80 - pF capacitor connected across a 110 V, 50 Hz, single phase supply is shown in the figure below. Calculate the current in the individual element, the total current drawn from the supply and overall power factor of the circuit. Draw a neat phasor diagram showing Ie. Ik and lc. R=250 L-64 mH e C= 80 uF 110 volt, 50 Hz supply

Q: A 1-m length of tungsten wire draws 5 A when connected across a battery. The wire is then cut into…

A: The tungsten wire will have resistance, the above circuit can be thought of as if a battery is…

Q: 5/Which of the following circuit element receives energy? a. Active Element b. Passive Element c.…

A: The explanation is as follows.

Q: If the voltage on pin A3 is 0.806V, what value will analogRead(A3) return from the ADC?

A: Take reference voltage Vref=5V and 10-bit ADC. By using 10bits we can able to represent data  in…

Q: How you will read this graph? How much is the inrush current

A: Inrush Current:- The current that is absorbed by a transformer during transformer energization is…

Q: If a small power system has a  base power of 5.0 MVA and base current is 1000 A, the base voltage…

A: Given: Base power =5MVA Base current= 1000 Formula used: P=VI

Q: What is the difference between the pins under number 1 and the pins under number 4, and mention when…

A: The difference between pin 1 and pin 4 is the transmitting ability (information) to external…

Q: A circuit is q5 indicated in the STanged the value of the current n eac gure belaw, the ye being as…

A: In the circuit, RLC are consist in the series parallel.  Find the current in each branch.

Q: A mixed circuit is shown in the figure below. For each resistor, its voltage and current, as well as…

A: Given circuit,Asked to find,Total resistance seen by source.The current through each resistor.The…

Q: Determine the voltage dropped on R3, given: E₁ = 236 V, R₁ = 39 , R₂ = 75 , and R₂ = 150 (Round the…

A:

Q: Complete the table: Show complete and neat solution. Round off answers up to the 4th decimal place.…

A:

Q: Draw the voltage tripler circuit and explain its operation. Explain the difference between voltage…

A: The detailed answer is solved below according to the given parameters and instructions in the…

Q: 5. How much charge is represented by 4,600 electrons?

A: This question belongs to Circuit theory. It is based on the presence of charge on electron.

Q: What are the values of R,R, and R, ? 18 0 A B A B Ri 36 0 272 R: (a) 120,6Ω, and 8Ω (b) 6012N, and…

A: Given: RAB=18 Ω RBC=27 Ω RAC=36 Ω Solution: By Delta to Star transformation, R1=RAB×RACRAB+RAC+RBC…

Q: 1.5L 1-5A 1.55L Reg = ?? %3D

A:

Q: Complete the table: Show complete and neat solution. Round off answers up to the 4th decimal place.

A:

Q: V2 No R2 FRI V3 Is手R キRo No V. Rs 幸&

A:

Q: 1. Consider the following closed-loop system. L(s) 1 S R(s) Σ (a) open-loop transfer function? (b)…

A: Given system,

Q: Find the eurrent geross Ior resistos tokr

A:

Q: Determine RAB 240 4.8Q 3.8Q 8.50 6.30 3.8Q 790 180 - 3.50 3.70 140 6.90 a 0.70 450 3.70 W 480 320…

A:

Q: How can this be represented on Tinkercad?

A: The given circuit isWe need to represent the above circuit on Tinkercard.

Q: A fully-charged power bank with a full capacity of 100,000 mAH is used to supply a DC lamp of 12…

A:

Q: Practical results Figure 3: Figure 3: Figure 4: Figure 4 IL (mA) VL(volt.) IL(mA) VL(volt.) RL (ohm…

A: Figure 3     IL ( mA)     For different values of RL the practical results of current  are less than…

Q: If R₁ = 63 Q and E₁ = 79 V, what is the power of R₁? (Round the FINAL answer to one decimal place.)…

A:

Q: The values of determines whether the response is overdamped, underdamped or critically damped a. R,…

A: Resistors, inductors and capacitors form an integral part of any electrical circuit. A source,…

Q: for part c what is the actual calculation?

A:

Q: Electrical Power. Create ten electrical energy questions and answer it.

A: Electrical power- Electrical Power is define as the rate of electrical energy transmit through an…

Q: Please help me make these two circuits on TinkerCAD. I am having trouble understanding how to make…

A: Need to connect the given circuit in the tinkercad and then analyze the circuit with various input…

Q: reading is due to the a. insertion O b. loading effect с. c. battery aging d. O d. conversion

A: In this question we will write about loading effect....

Q: Explain in detail what happened to the current and voltage measurements as S1 and S2 (2nd pic…

A: Set 1 (S1) and Set 2 (S2) are switched places. The tables are as shown below,

Q: are the Factors that aFfect the Value of electrical Resistance2 Q-2) Find the value of the Following…

A:

Q: Ic=? VCE = ? 180 kr 20V. {.5KQ 5km Ic UCE B = 100

A:

Q: HIGH Jo J2 Q, K1 K2 K3 CLK

A: By observing the above circuit it can be concluded that, For JK flip flop the next state can be…

Q: Determine the current flowing through resistor R₁, given: E₁=194 V, R₁ = 222, R₂ = 25 02, R₂ = 152,…

A: The given circuit is ET=194 V.R1=22 Ω.R2=25 Ω.R3=15 Ω.R4=29 Ω.We need to find the current flowing…

Q: ct Fluke T5 and DMM Questions These questions apply to the T5 and/or the Fluke DMM. You will likely…

A:

Q: The temperature range for the flash steam power plant is---- O a. 350 F O b. 840C c. 840 F O d. 350…

A: flash steam power plants are capable of operating in certain range of frequencies only , based on…

Q: What is the final position of the Spot trace in the CRO Screen if DC voltage is applied to the y…

A: CRO- Cathode Ray Oscilloscope- CRO mainly consists of a cathode ray tube. The main component of…

Q: 1. Solve the tollowing unknowns. Tabulate your answer. R1 R2 Vs -ov R3

A:

Q: If the voltage on pin A3 is 0.752V, what value will analogRead(A3) return from the ADC?

A: Given, Voltage on pin A3 (V) = 0.752V We know, for ADC, Resolution bits (n)=10  The reference…

Q: Assignment is formatted so we can see what we need to answer if that makes sense, if it violates the…

A: Step 1: As we move from left to right, observe the transitions marked as A, B, C and D: Step 2:

Q: In order to select the chip A19-A15 must be set to ______. A. 10100 B B. 01011 B C. 00101 B D.…

A: As the gate shown in figure is NAND gate. But in the output side At CS another bubble is present…

Q: Fill in the Blank: A 66 block is a block which has 25 rows of four metal pins.

A: A 66 block is a telephone wire distribution system.

Q: t?

A: From the figure the battery voltage can't be identified but evidently from the voltage reading of…

Code Conversion

The method or technique used to convert code from one format to another is termed code conversion. Code conversions are most commonly used in computers, digital electronics, microprocessors, etc.