6. A horizontal force of P-100 N is just sufficient to hold the crate from sliding downthe plane, and a horizontal force of P-350 N is required to just push the crate up theplane. Determine the coefficient of static friction between the plane and the crate, andfind the mass of the crate.

Step 1:Step 2:Step 3:Step 4:Step 5:Therefore,

Answered: 6. A horizontal force of P-100 N is…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

9. A concentrated load P is supported by two bars as shown below. Bar (1) is made of cold- rolled red brass [E =16,700 ksi; a =10.4 x 106 /°F] and has a cross-sectional area of 0.250 in.². Bar (2) is made of 6061-T6 aluminum [E= 10,000 ksi;a=13.1 x 106 /°F] and has a cross-sectional area of 0.425 in.². After load P has been applied and the temperature of the entire assembly has increased by 40°F, the total strain in bar (1) is measured as 1,400 μe (elongation). Determine: (a) the magnitude of load P. (b) the total strain in bar (2). | 40° (1) 55°
A 250 kg crate is subjected to forces F1=790N and F2=1300N. The coefficient of kinetic friction between the crate and the surface is 0.23. Assume angle 1 = 38 degrees and angle 2 = 15 degrees. a. determine the normal force developed between the crate and the surface. b. if the crate is originally at rest, determine the distance it slides in order to attain a velocity of 8.5m/s.
The 9-lb block has a velocity of 6.72 ft/s when the force of F = (257.6t²) Ib-ft/sec2 is applied. Determine the velocity of the block whent = 2.40 s. The coefficient of kinetic friction at the surface is µ = 0.31. Answer is in %D ft/sec F = (257.6t) Ib-ft/sec2
The top box weighs 125 lbs. and the bottom box weighs 150 lbs. The coefficient of static friction between the boxes is? = 0.6. The coefficient of static friction between the bottom box and the floor is 0.35. What force, P, will cause movement of one or more of the boxes? Does it tip or slip? (Hint: You must determine the minimum force to get the top box to slide; the top box to tip, both boxes to slide, and both boxes to tip. The answer will be the smallest.) 5 ft -3 ft 4.5 ft 4.5 ft B
L+I 7 (ab)" a-bm f 2 1 TY –314 - 2- 6 STATICS ENGINEERS MECHANICS CHAPTER Lecture Notes: = m %3D EXAMPLE: 22 einber 6O 3.45 m 1.25 m + 3 Pz 1.85 m 1 1.22 m Wa120 IN A weight W• 120 kM is being supported by steel sections with force T. force and force C. The coordinates of A. B. C. and D are given. Assume that E is the origin (0.0.0). Determine Forces T. F, and C.
Plastic moment and plastic sectional module for a beam
The 79-lb force P is applied to the 200-lb crate, which is stationary before the force is applied. Determine the magnitude and direction of the friction force F exerted by the horizontal surface on the crate. The friction force is positive if to the right, negative if to the left. Assume μ = 0.42, μk = 0.34. P Answer: F= i Mk lb Attempts of 1 od
Construct the V and M diagram of the beam loaded as shown. Answer: Max. Moment = 40 KN 20 kN/m 50 kN 100 kham A D ET 0.5 m *- 1.5 m-0.5 m0.5 m+ Boam: -1 m 2 m
solution?
A 50 meter steel tape is suspended in the air between a transit and a vertical rod which is placed exactly at the 50 meter mark. The slope of the measured line is 1 degree and 30 minutes. The tension on the tape is 10 kg, and the weight of the tape per unit length is 0.05 kg/m. What normal tension (N) is required in order that the effect of sag will be eliminated when the tape is supported at end points only? The standard pull is 10kg. Tape area is 8 mm2. E = 200 GPa. * 38 378 O 45 O 441
1. Please show your complete solution.
The 40 kg block is placed on a 30° inclined and released from rest. The coefficient of static friction between the block and the inclined plane is 0.30. A) Determine the maximum value of the initial tension T in the spring for which the block will not slip when released. B) Determine the minimum value of the initial tension T in the spring for which the block will not slip when released. C) Determine the friction force on the block if T = 150 N.

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

6. A horizontal force of P-100 N is just sufficient to hold the crate from sliding down the plane, and a horizontal force of P-350 N is required to just push the crate up the plane. Determine the coefficient of static friction between the plane and the crate, and find the mass of the crate.