6. A heat exchanger was installed purposely to cool 0.50 kg of gas per second. Molecular weight is 28 and k=1.32. The gas is cooled from 150 deg C to 80 deg C. Water is available at the rate of 0.30 kg/s and at a temperature of 12 deg C. Calculate the exit temperature of the water.

6. A heat exchanger was installed purposely to cool 0.50 kg of gas per second. Molecular weight is 28 and k=1.32. The gas is cooled from 150 deg C to 80 deg C. Water is available at the rate of 0.30 kg/s and at a temperature of 12 deg C. Calculate the exit temperature of the water.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Compressed liquid

A: Given Data: The pressure of liquid water at the inlet of the steam generator is, P1=10 MPa. The…

Q: Hot gases (c=1.10 kJ/kg.K) enters an adiabatic heat exchanger at 237°C & 130 kPa while Saturated…

Q: Q1] A shell and tube heat exchanger is used to heat water (C₂= 4236 J/kg. "C) from 80°C to 150°C at…

A: The specific heat of water is Cpw=4236 J/kg°C The specific heat of gas is Cp(gas)=1040 J/kg°C. The…

Q: Winter air is heated & humidified thru steam heated coil and humidified using water sprayer. Air is…

A: The answer is given in the below attachment

Q: mnot Thot = 75°C Tout-? mcold Teota = 18°C %3D Hot and cold stream of water are mixing together as…

Q: Derive the equation of continuity of a component in multicomponent mixture?

A: To derive the equation of continuity for a component in a multicomponent mixture, we start with the…

Q: (a) Liquid water in a tank can be converted into ice just by evacuating the air from the tank…

A: (a) In general atmospheric conditions, the pressure of the atmosphere lies on the water in liquid…

Q: M not Thot = 75°C Tout-? %3D mcold Tcotd = 18°C Hot and cold stream of water are mixing together as…

Q: 1 Water (u 0.001 kg/m.s) is siphoned from a large tank and discharges into the atmosphere through a…

Q: Dry saturated steam at 8 bar expands in a convergent nozzle to a pressure of 05 bar and 0.8 dryness…

A: Given Data: Inlet pressure, P1=8 bar Exit pressure, P2=0.5 bar

Q: water at 366 k is transfer from storge tank to another at rate 50 m3/min .The pump supplied work at…

Q: 2. Forced air flows over a heat exchanger in a room heater, with a convective heat transfer…

A: Convective heat transfer coefficient = 150 BTU/ hr-ft2 F Surface temperature = 200 F Room…

Q: 2 m^3/min of a light oil are to be heated from 20C to 100C (with zero vaporization) in an exchanger…

Q: The air conditions at the intake of an air compressor are 33 C, 50 percent relative humidity, and…

A: The intake temperature of the air is T=33°C. The relative humidity of the intake air is ϕ=0.5. The…

Q: mhot Thot = 75°C Tout-? %3D mcold Tcold = 18°C Hot and cold stream of water are mixing together as…

Q: In a gas urbine unit. the gases flow through the turbine is 15 kg's aud the power developed by the…

A: We have to slove

Q: air at 30 ℃ and RH 40% flowed to the heating coil so that the dry bulb temperature was 80 ℃. then…

A: Given State 1: DBT 30 deg C and RH 40% State2 by heating: DBT 80 deg C State 3 by passing into pet…

Q: CO2 gas enters the pipe at a flow rate of 2kg / s, 3MPa pressure and 500K temperature. While the CO2…

A: Given, mass flow rate (m˙) = 2 kg/s P1 =P2= 3 MPa T1 = 500K T2 = 450K

Q: rite down the steady flow energy equation (SFEE) and apply it for boiler, turbine, heat exchanger…

A: An open system's total energy fluxes are described by the Steady Flow Energy Equation. The mass…

Q: In mixing tanks systems, the water comes in at a rate of 4L/min in Tank A. This tank contains 500L…

A: Given

Q: a supply tank having 14m long and 1.7m diameter is used to store fuel oil with 34degree API at…

Q: Liquid water is heated inside the tubes of a shell and tube heat exchanger as shown in the figure…

A: Given data The mass flow rate in each tube is m˙=0.25 kgs. The diameter of the inside tube is di=16…

Q: The initial state enthalpy for water (h3(kJ/kg)) is equal to: The final state enthalpy for water…

A: For solution refer below images.

Q: 2 Hot Cold water water STATE DATA FOR SYSTEM di 210 3 T1 mm vi m/s °C 95 P1 1.0 bar d2 180 mm V2 m/s…

Q: In a palm oil processing plant, the crude oil is heated using hot water from a furnace. The furnace…

A: Heat exchangers are devices that allow heat to be transferred between two fluids via a separating…

Q: Steam is delivered to turbine at 5.4 MPa and 600 degree C. Before condensation at 31 degree C, steam…

Q: Water inter a condenser at a mass flow rate of (2.5 kg/s) and (21 kPa and 65 C), and exit with (h=…

Q: A heat exchanger, shown below, is used to cool an air flow from 550 K to 250 K, both states at 1…

Q: Exhaust gasses from a diesel engine are used to heat water in an insulated heat exchanger. Refer to…

Q: The initial state enthalpy for air (h,(kJ/kg)) is equal to: The final state enthalpy for air…

A: Given Data State 1: Air, 550 K,1 MPa State 2: Air, 250 K,1 MPa State 3:Water,30°C,0.1 MPa State…

Q: mrot Tnot = 75°C Tout-? mcold Tcoa = 18°C %3D Hot and cold stream of water are mixing together as…

Q: Steam enter a ingle stage impulse steam turbine with an inlet velocity of 50 m/s and leaves with and…

Q: Milk is flowing through a heat exchanger at a rate of 2000 kg/h. The heat exchanger supplies 111,600…

A: Given Data Mass flow rate= 2000 kg/h Q=111600 kJ/h T₀ =95°C C=3.9 kJ/kg.K

Q: A combustion chamber consists of combustion pipes with a diameter of 15 cm. Compressed air enters…

A: We have to determine the air, at the exit of the combustion chambera) temperature,b) pressure,c)…

Q: ou are designing an electric air heater for large conference rooms. A 75mm OD, 4mm wall thickness…

A: Given Data: The outer diameter of the pipe is D = 75 mm. The wall thickness of the pipe is t= 4 mm.…

Q: P;=1 MPa T;=800 K P2 = 0.1 MPa T;= 400 K SOLID-OXIDE FUEL CELL moles no, = 105 moles 02 = 105- u, =…

A: following is the answer to the above question- 8l

Q: Water enters a heat exchanger operating stably at P = 10 bar and T = 80oC, given that the outlet is…

A: GivenP1=10 bar T=80oCAt outletP2=10 bar saturated steam

Q: ●Water enters a boiler at 22.000C at atmospheric pressure through a pipe at an average velocity of…

Q: Water at 15°C is pumped from a reservior at a rate of 0.1131 m3/s where the local atmospheric…

Q: 0% fresh air at 40°C DBT an nd 50% RH. The air leaves ti Cal cooling load and room heat

A: given:

Q: kg 2kg Of air at 500 K is mixed with 1.6 of air at 900 K in an insulated chamber S The resulting…

Q: Leftover air at 20ºC and 100kPa is driven by a fan through a horizontal galvanized conduit of 1 m in…

Concept explainers

Heat Exchangers

Heat exchangers are the types of equipment that are primarily employed to transfer the thermal energy from one fluid to another, provided that one of the fluids should be at a higher thermal energy content than the other fluid.

Heat Exchanger

The heat exchanger is a combination of two words ''Heat'' and ''Exchanger''. It is a mechanical device that is used to exchange heat energy between two fluids.

Question

100%

6. A heat exchanger was installed purposely to cool 0.50 kg of gas per second. Molecular weight is 28 and k=1.32.
The gas is cooled from 150 deg C to 80 deg C. Water is available at the rate of 0.30 kg/s and at a temperature of
12 deg C. Calculate the exit temperature of the water.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Q4. (a) Liquid water in a tank can be converted into ice just by evacuating the air from the tank without using heat exchanger. Explain the process and how the device works and the process can be made more efficient. (b) If you have two pots with the same volume but different shapes, one is tall and narrow the other is wide and short, compare and explain about the boiling temperature of the two cases. Discuss the reason why the required temperature for the two cases are different or same on the basis of your answer.
A (1.5 kg/s) of water vapor inters a condenser at (20 kPa and 60°C), and exit with (h= 251.5 kJ/kg). Find: a) The mass flow rate of water flow at the exit sections b) The rate of heat removed from the water in the condenser From table T=90C & P=70 kPah=2660 kJ/kg
4. The following heat exchanger uses 10 kg/s of hot air to heat and boil liquid water into saturated steam at 500 kPa. (a) Find the steam flow (kg/s) (b) Determine whether the process is allowed by the second law (Answer: It is not!) (c) On the surface, the process looks OK as Tair>Twater at both the inlet and outlet. You should be able to see the problem if you sketch the air and the water temperature profiles as you move left to right through the exchanger. (Hints: The air will be essentially a straight line, while the water will not. For the water, think about what happens when it is changing phase.) This is called a pinch point violation, and it is a very important design consideration in advanced combined cycle systems and in nuclear power plants. Air 100 kPa 160°C 10 kg/s Saturated Vapor 500 kPa Air: 160°C Steam: 151.8°C Q Air 100 kPa 30°C Liquid Water 500 kPa, 20°C Air: 30°C Water: 20°C
CO2 gas enters the pipe at a flow rate of 2 kg / s, 3 MPa pressure and 500 K temperature. While the CO2 pipe type is flowing, it is cooled down at constant pressure and its temperature drops to 450 K at the pipe outlet. Find the ideal gas using the equation.
Heat exchangers exchange only heat and not mass (fluid does not mix).The working fluid is water vapor that comes from a boiler and serves to heat cold water.Suppose that in this hypothetical application above, the water vapor enters at 500 kPa and 300 °C through the “pipe inlet” (see figure) and so is used to heat the cold water, which enters in the opposite direction through the “hull inlet” ” at 15 °C and goes to the “hull exit” exiting at 75 °C. How much steam per kg of liquid water is needed as long as the steam does not condense?
Steam at a pressure of 28kpa is passed into condenser and it leaves as condensate at a temperature of 592 0 Cooling water circulates through the condenser at the rate 9 of 45 kg/min. It enters at 152 and leaves at 30°C.It the Steam flow rate is 1.25 kg/min, determine the dryness r fraction of Steam as it enters the condenser.
Solve the following problem and show your complete solutions. explain your answer for better understanding
I need the answer as soon as possible
Combustion Engine Question is image