6. A 1: 25 scale model of a ship has a submerged surface area of 6 m², a length of 5 m and experiences a total drag of 25 N when towed through water with a velocity of 1.2m/s. Estimate the total drag on the prototype when cruising at the corresponding speed. The skin friction force can be estimated by F. = C Ap V2/2 where the coefficient C = 0.0735/(Re)1/5 S Assume water = 1 x 10-3 Pa.s and both model and the prototype. P = 1030 kg/m³ for water

6. A 1: 25 scale model of a ship has a submerged surface area of 6 m², a length of 5 m and experiences a total drag of 25 N when towed through water with a velocity of 1.2m/s. Estimate the total drag on the prototype when cruising at the corresponding speed. The skin friction force can be estimated by F. = C Ap V2/2 where the coefficient C = 0.0735/(Re)1/5 S Assume water = 1 x 10-3 Pa.s and both model and the prototype. P = 1030 kg/m³ for water

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the tension T in the belt needed to overcome the tension of 200 lb created on the other side. Also, what are the normal and frictional components of force developed on the collar bushing? The coefficient ofstatic friction is μs = 0.21.
A 10-lb force is pushing the 40-lb block as shown. The incline angle of the plane is α=40º . The coefficient of static friction between the block and the incline is μs = 0.75 and the coefficient of kinetic friction is μk = 0.65. Will the block slide on the plane? If it does, will it slide up or down the plane? What is the friction force between the block and the plane?
The wheel weighs 20 lb and rests on a surface for which μB = 0.2. A cord wrapped around it is attached to the top of the 30-lb homogeneous block. If the coefficient of static friction at D is μD = 0.3, determine the smallestvertical force that can be applied tangentially to the wheel which will cause motion to impend.
4. A 25 mm diameter shaft is pulled through a cylindrical bearing as shown (not rotating). Oil is used as a lubricant and fills the 0.3 mm gap between the shaft and the bearing. The kinematic viscosity of the oil is 8.0 x 10-4 m²/s and the specific gravity is 0.91. Determine the force P required to pull the shaft at a velocity of 3 m/s. Assume the velocity distribution in the gap is linear (i.e. Couette flow). Draw the free body diagram and show the forces. Bearing Shaft 0.5 m- Lubricant
A block with mass (m = 19.5 kg) is pulled with a force (F = 280 N) 0 = 25°. a) Draw a free-body diagram. b) Find the normal force. c) If coefficient of friction between the crate and the surface is uz=0.12, what is the value of the frictional force, fr. d) Find the acceleration. e) What minimum horizontal force is needed to move the block with a constant speed (while keeping the F = 280 N)? F m
The crate, which has a mass of 100 kg, is subjected to the action of the two forces (Figure 1). If it is originally at rest, determine the distance it slides in order to attain a speed of 6 m/s. The coefficient of kinetic friction between the crate and the surface is uk = 0.2. Mk 800 N 30°/ Figure 1 1000 N 3
Problem 2 Determine the force P required to lift the M-kg steel crate which rests against a 5° - wedge on a side and brick wall on the other side. The coefficient of frictions between the crate and wedge, wedge and surface, crate and surface are 0.45, 0.35, and 0.38, respectively. Use the following values, M= 90 kg, and g = 9.806 m/s? Зт 19° 1.2m 21°
The 113-lb force P is applied to the 230-lb crate, which is stationary before the force is applied. Determine the magnitude and direction of the friction force F exerted by the horizontal surface on the crate. The friction force is positive if to the right, negative if to the left. Assume μs = P Answer: F = 0.48, Mk = 0.38. i Mk lb
Question 2: A 40 lb suitcase slides down a 20ft ramp with an initial velocity of va= 10 ft/sec. The coefficient of kinetic friction on the ramp is equal to 0.2. Determine the point where it strikes the ground at C and how long it takes to go from A to C. A/ 20 ft 30 B 4 ft C -R-
Problem 4: A film of oil exists between two horizontal plates spaced 3mm apart. The lower plate is fixed and the upper plate is pulled with a constant velocity. The velocity profile between the two plates is found to have a non- linear profile that is defined as u = (9y - 0.6y?) mm/s where y is in mm. Assuming the top plate has an area of 0.5 m? and the viscosity of the oil is u= 0.437 N.s/m?, determine (a) the shear stress 1mm above the fixed plate, and (b) the force required to pull the upper plate. 2. F 3 mm
Determine the magnitude of the friction force acting on the 100kg block shown if P=100N. The coefficient of friction is 0.20. The forces applied to the block is initially at rest.
Problem #4 (. A 16-lb bowling ball is cast horizontally onto a lane such that its initial angular rate wo = 0 and its center of mass has a velocity vo = 8 ft/s. The radius of the ball is r = 0.375 ft, and the coefficient of kinetic friction between the lane and ball is Hk = 0.12. 8 ft/s G What is the condition, in terms of w and v for а. 0.375 ft rolling without slipping? b. ) Draw a clear and complete free body diagram of just the ball. с. What is the angular acceleration of the ball? Use IG = l5 mr for a solid sphere. What is the linear acceleration of the ball? е. For how much time does the ball slide before it begins to roll without slip? f. For what distance does the ball slide before it begins to roll without slip? g. What is the velocity of the ball at the moment it beings to roll without slip? d.