6) You work as an engineer in a company and you have been given the assignment of measuring the electrical conductivity and the band gap (Eg) of a new intrinsic semiconductor material at 20 and 100 °C. You cut this material in the form of a rectangular prism with a length of 30 cm, a width of 1 cm and a thickness of 2 cm, and you applied a potential difference of 1 V by placing electrodes on the faces shown in the figure. In this case, you measure a current of 0.8A at 20 °C and 12A at 100 °C. According to this information a) calculate the electrical conductivity of the material at 20 and 100 °C and b) the band gap of this material. 30 ст 2 ст 1 cm

6) You work as an engineer in a company and you have been given the assignment of measuring the electrical conductivity and the band gap (Eg) of a new intrinsic semiconductor material at 20 and 100 °C. You cut this material in the form of a rectangular prism with a length of 30 cm, a width of 1 cm and a thickness of 2 cm, and you applied a potential difference of 1 V by placing electrodes on the faces shown in the figure. In this case, you measure a current of 0.8A at 20 °C and 12A at 100 °C. According to this information a) calculate the electrical conductivity of the material at 20 and 100 °C and b) the band gap of this material. 30 ст 2 ст 1 cm

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A silicon diode has an incremental resistance “R”. It is then connected in series with a resistor 25 ohms across a 25V source. If the voltage drop across the 25 ohm resistor is 10 V, what is the value of “R” ?
1) It can be accepted that D1 and D2 diodes are from the same family in the circuit given in the figure. a) output voltage, wwwiwwwww wwwww wwwwwwwwwwn w www w 0.33 k2 wwwwww wwwww E 10 V D Si D, Si b) the current flowing through the resistor, ww ww c) currents flowing through the diodes గ wl ww ww calculate. www ww +
*Use 4 decimal places. For the circuit below, determine the diode voltages VD1 and Vp2, diode currents Ip1 and Ip2, and voltage across the resistor, VRLIMIT- Use ideal model. Assume r'd (for both diodes)=200. Note D, is Germanium, D2 is Silicon, VBIAS = 14V and RLIMIT = 760 ohms . VD1 = Blank 1 V; VD2 = Blank 2 V; Ip1 = Blank 3 mA; Ip = Blank 4 mA ; VRUMIT = Blank 5 V ... Capture3.JPG +Vp1- +VRLIMIT- +Vp2- Ip2 BIAS
Please make a concept map of the covalent link theme for semiconductors with the following subtopics, you can add tables, graphs, images, or things you think are relevant 1.5 Driving process 1.5.0 Introduction 1.5.1 Mobility 1.5.2 Relationships between carrier equilibrium concentrations 1.5.3 Detailed balance principle 1.5.4 Carrier equilibrium concentrations in homogeneous semiconductors 1.5.5 Conductivity 1.5.6 Hall Effect
Determine the value of voltage across R1 and value of R2 in the given circuit if a current of 4.1 mA is flowing through the diode when a forward bias voltage of E=10 V is applied and R1=330 Ohms. Assume diode as silicon. R1 D2 'E R2 Voltage across R1 Resistance of resistor R2
From the diode circuit shown below, If E=30 V and RL=802, determine the current supplied from the battery, the voltage across the load resistance, and the voltage across diode D2 if all the diodes are silicon with an internal resistance of 1 2. D . RL D4 D3 a. The Current supplied by battery is b. The Voltage across Load resistance RL is c. The Voltage across diode D2 is
Please answer both question or give someone else to answer. Need small explanations. Which of the following are the majority carriers in p-type semiconductors? a. electrons b. photons c. holes d. neutrons Two capacitors C1 = 1.5 μF and C2 = 5 μF are in series. If the charge stored by C1 is 10 C, determine the charge stored by C2. a. 3 C b. 10 C c. 1.5 C d. 4 C
3. In the following circuits, given source voltage Vs=9V, R1, R2 and R3 all are 1kOhms. Answer the questions by considering the diodes as ideal and practical silicon ones respectively. Vs Vs Vs R2 R2 R2 Vout P D R1 R1 R3 R1 (a) Vout = ? (b) Vp = ? (c) Vp = ? Note: Vp means the voltage at point p. w
A- If V, is a sinusoidal voltage with Vm = 40 V, and V= 15 V. Plot the waveform of the output voltage in each of the following clippers circuits assuming ideal diodes. B- Repeat part (A) if the diodes are silicon diodes. R R R (a) (b) (c) (d)
In the figure given we have u(t)=10- cosot [V]. We assume the diodes and the A-meter (A) to be ideal. a) Plot the waveform of the current flowing through the A-m in scale. b) What is the reading of the A-m, if it is moving-coil type? A u(t) R1 R2 c) What is the reading of the A-m, if it is moving-iron type? d) Calculate the power factor of the WHOLE structure. 5Ω 10Ω
4.) In which mode will a diode generally not conduct electricity? a. Bidirectional Biased b. None of these c. Forward Biased d. Reversed Biased 5.) Consider the following schematic symbol of a semiconductor device: Which side is the Cathode? (Picture inserted down below) a. Side A b. Both side A and B c. Side B d. Neither side A or B 8.) Integrated circuits can be broken down into three basic categories. Which category does an operational amplifier (or op-amp) fall into? a. Analog b. None of these c. A combination of analog and digital d. Digital
5V 3000 1000 . 2m 1 Si 4000 500 12V The circuit shown in Figure 1 contains a Si diode with a diode resistance on 1000. Use the piecewise linear model to solve the circuit. • How many nodes are in the circuit? • Determine the Thevenin voltage across the diode. Replace the diode with the appropriate model and then solve the circuit to determine the power dissipated by each resistor and the diode.