6 Ohm 1 mH 18 VI50 Hz/0 Deg 3 A/50 Ha0 Deg 1 uF Ohm Fig.2 Tablel Measured values Zth Eth Itoad Calculated values Zth Itoad Discussion 1. Calculate thevenin impedance Zth and record the value in table 1 2. Calculate thevenin voltage source Eth and record the value in tablel 3. Calculate the current through the load 22 resistance then record the value in table 1 4. Discuss the result.

6 Ohm 1 mH 18 VI50 Hz/0 Deg 3 A/50 Ha0 Deg 1 uF Ohm Fig.2 Tablel Measured values Zth Eth Itoad Calculated values Zth Itoad Discussion 1. Calculate thevenin impedance Zth and record the value in table 1 2. Calculate thevenin voltage source Eth and record the value in tablel 3. Calculate the current through the load 22 resistance then record the value in table 1 4. Discuss the result.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Pn balanced3phase system the Sequguce is Positive and'aline Voltage Vbe=208/-70V The load is balancet also Yin farallet with Arthe phoase impedaacesof the two load are 5362 0,3-j92/¢ resfectively The tine impedance is lofija82/4 Draw the single phase equivelent circuit and use It te calculate'the Line Valtage at the load in the a-phase Find totaj Powerloss in Line-
Pls do al step and readable
|x(t) |h(t) 1 6. 1 2 3 Fig. 4c d) Prove the width property of convolution in (c).
We wish to design the circuit shown in figure for a voltage gain of 0.7 with a power budget of 3 mW. Compute the required value of W/L. Assume C, is very large and = 0. Şekilde gösteritern devreyi güç tüketimi 3 mW ve gerilim kazaner 0.7 elacakitare asantaurat istiyoruz. Gerekli W/esernthesupia toik olduğunr ve=0 kabul ediniz. Circuit parameters / Devre Parametreleri HnCox = 200 µA², VDD = 1.8 V, VTH = 0.4 V, R = 602 VDp = 1.8 V VinoHEM1 C1 Vout O a. 1745 O b. 1620 O c. 2836 O d. 1890 O e. 3241 O f. 2062 O g. 2521 O h. 2269
2. Calculate V, in this circuit. A) 5.55286.31° V 10236 V B) 4266.87° V C) 5230° V D) 2266.87° V - j³r Aukto 252 252 V₂
100% © uo 9:18 1 • Asiacell Ilı. docs.google.com a 1 phase half bridge inverter having dc input voltage 3ooV , and purely resistive loadR = 2.4 ohm , find : VDC/2 A D1 R VDC/2 A D2 Vrms for the first harmonic:* 100 Volt Other O 150 Volt O 135 Volt
Identify the loads which does not require a neutral. B 415V 415 V A 240ν C 240 V 240 V DI 240 V E F 415 V a. Load A & F b. Load A & B O c. Load E & F d. Load C & D
Sequçuce P n balanced sphase system the is positive and'aline Voltage Vbe=208/-10V Fhe toad is bataacet also Y in faratlet With Arthe phase impedaacesof the tuo load are 5362 , 3-j92/¢ Fesfectively. The tine imfedance is li4ija8214 praw the Singte phase equivelent cipcuit -and use lt to the load in the a-fhase Find total Pawlerloss in Linee calculate'the Line Voltage at
Solve the voltage V1 of the given circuit below. Si +32V 4.7k oVo + V1 - V2 8kn - 8V 8.6 V 14.52 V 23.08 V 11.84 V
Using Wye-Delta Conversion. Find Req and I .
The values of the circuit elements are given below.Accordingly, what is the maximum power transfer that can be made to ZL? V=11.7 phase 30 VR=12 ohmsL=j20 ohmsC1=-j14 ohmsC2=-j8 ohms
i need the answer quickly