Answered: 6-A lossless T.L. has Zo = 100 Q and is…

6-A lossless T.L. has Zo = 100 Q and is loaded by an unknown impedance . Its VSWR is 4 and the first voltage maximum is ^/8 from the load Find the load impedance .

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.61P

See similar textbooks

Related questions

Q: 2. Utilities may use the Open-Wye/Open-Delta connection for three-phase transformers when…

A: a) Determine the voltages, here it is tapped at 12: Van=-VAN×240120×12=-12.47 kV (negative sign due…

Q: For the ideal transformer circuit of figure shown below, find (a) 1₁ and 12: (b) V₁, V2 and Va the…

Q: A transformer shown in Figure 10 is needed that will cause an actual load resistance of 250 to…

A: (a) Redraw the given circuit diagram.

Q: The circuit shown in figure EM1-1 shows an AC voltage source VAC connected in series with a load…

A: We need to find out resonance frequency and impedance at resonance frequency.

Q: A non magnetic medium has an intrinsic impedance 360Z30° Q. The loss tangent is

A: Wave is function of space and time. Frequency below which attenuation occur and above which…

Q: Given Zc - j339 , R₁ = 414 , RL = 12420 2 and a=0.24, what is the magnitude of the source voltage Vs…

Q: Three impedance Za= (3+j4) ohms, Zc= (4-j4) ohms and Zr=0+j3 ohms are connected in parallel. Solve…

A: Here, Za= (3+j4) ohms, Zc= (4-j4) ohms and Zr=0+j3 ohms are connected in parallel

Q: Design a flyback converter for an input of 24 V and output of 40 W at 40V. Specify the transformer…

Q: What do the connection angles and groups show in transformers? For example, where are the Yy0 , Dy5…

A: It is asked what do the connection angles and groups show in transformers. Also it is asked where…

Q: Please solve thiss questionnnnn

A: For Y connection, Iph = IL For delta connection, IL = Iph * 3 In our case, Y to delta turn ratio is…

Q: The impedance ZL in the circuit shown in Figure is adjusted for maximum average power transfer to…

A: (a) Remove the load impedance from the circuit and draw an equivalent circuit including the mutual…

Concept explainers

Compensation Techniques

The compensation techniques are the methods that are employed in the electrical control systems to enhance the performance of the system. The performance are generally affected by the factors like lag in the compensating devices, slow response of the system of the components like sensors used in the control system. The basic compensation technique involves lag compensation, lead compensation or the combination of the both.

Question

6-A lossless T.L. has Zo = 100 N and is loaded by an unknown impedance
Its VSWR is 4 and the first voltage maximum is A/8 from the load .
Find the load impedance .

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Compensation Techniques in Transmission Line

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

I need the answer at 20 minute
Consider the following circuit used to provide power for an induative RL load. The input voltage is V-100V and the load has a 50 impedance value. The thyristor is working at a frequency fs = 2 kHz. The discharge current is to be limited to 40A and the required dv/dt is 40V/us. If the value of Ce is equal to 0.14uF, then the snubber losses are equal to: R. V. Select one: O a 5.4W O b. 7.4W 1.4W Od. 3.4W
The step down DC chopper uses DC source voltage V(dc) = 200 V and resistive load impedance of 10 ohm. The duty cycle is 0.4 the voltage drop across the switch may be taken as zero, Calculate : (a) Average and RMS value of output voltage. (b) Average and RMS value of output current.
The temperature of a noninductive heater unit is controlled by a reactor. The heater unit and the reactor are connected in series across a 250 V, 60 Hz source. The voltage across the heater unit is 200 V. The voltage across the reactor is 100 V. The current in the circuit is 10 A. Determine: the power factor of the series circuit. the power factor of the reactor. the impedance of the reactor. the effective resistance of the reactor. the inductive reactance of the reactor
Having problem with this question. Please help me to understand.
Consider a series ac circuit containing an inductor and a capacitor. Knowing that the equivalent reactance XEqui. of the reactive components has a negative value, determine the phase relationship between the source voltage and current. Is the equivalent reactance inductive or capacitive? Determine the total impedance Z of a series ac circuit containing a resistor (R = 250 §), an inductor (X₂ = 150 M), and a capacitor (Xc = 200 (2).
I need help with the PSpice part. How do I do the PSpice stuff.
Which methods can be used to estimate or calculate the maximum power point on an I-V curve?
The rms value of v(t)=Vmaxcos(t+) is given by a. Vmax b. Vmax/2 c. 2Vmax d. 2Vmax
Design a flyback converter for an input of 24 V and output of 40 W at 40V. Specify the transformer turns and magnetizing inductance, switching frequency and capacitor to limit the ripple voltage less than 0.5%.
6.33. A battery is charged from 3-phase supply mains of 230 V, 50 Hz through a 3-phase semicon- verter. The battery emf is 190 V and its internal resistance is 0.5 2. An inductor connected in series with the battery renders the charging current of 20 A ripple free. Compute the firing angle delay and the supply power factor.egalov region wa Pristavan thit Ans. 73.263°, 0.652 lag] 6.34. (a) A 3-phase full converter is used for charging a battery with an emf of 110 V and an internal resistance of 0.2 2. For a constant charging current of 10 A, compute the firing angle delay for ac line voltage of 220 V. Find also the supply power factor. (b) For the purpose of delivering energy from de source to 3-phase system, the firing angle of the 3-phase converter has been increased to 150°. For the same value of de source current of 10 A, compute the output ac line voltage.daiw
helpp