6-123. Segment A of the composite beam is made from 2014-T6 aluminum alloy and segment B is A-36 steel. The allowable bending stress for the aluminum and steel are (Tallow)al=15 ksi and (oallow)st=22 ksi. Determine the maximum allowable intensity w of the uniform distributed load. -15 ft- A 3 in. B 3 in. 3 in.

6-123. Segment A of the composite beam is made from 2014-T6 aluminum alloy and segment B is A-36 steel. The allowable bending stress for the aluminum and steel are (Tallow)al=15 ksi and (oallow)st=22 ksi. Determine the maximum allowable intensity w of the uniform distributed load. -15 ft- A 3 in. B 3 in. 3 in.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

determine the member stresses of the truss shown. indicate if the stress in the member is in tension or compression. present complete and neat solutions. p1-30kN W-25kN/m P2=51kN AH Av Im P₂ Im P₂ Im P₂ Im Av W 1.6m
AW18 x 40 standard steel shape is used to support the loads shown on the beam. Assume P = 20 kips, w = 4.8 kips/ft, LAB = 4.2 ft, Lec = 4.2 ft, and Lco = 16.0 ft. Determine the magnitude of the maximum bending stress in the beam. P B C D LAB LBC LCD Answer: Omax = i ksi
Compute the maximum force F (in KN) that can be applied to the composite rod if the allowable total deformation of the composite rod is limited to 0.80 mm A 6F B Steel Rod d = 100 mm L=3m E = 200 GPa C Aluminum Rod d = 70 mm L = 2m E = 70 GPa 3F D Bronze Rod d = 40 mm L = 4 m E = 80 GPa 2F
Derive the maximum steel ratio and the recommended rteel ratio fe' O.856 fy Po-004 3 0.85 fc' pooos= 0-85
Question # 2: The composite beam consists of a wood core and two plates of steel. If the allowable bending stress for the wood is 20 MPa, and for the steel 130 MPa, determine the maximum moment that can be applied to the beam. Ew = 11 GPa, Est=200Pa. 220 Gpa - 125 mm M * 20 mm 75 mm 20 mm
4. Determine the maximum load P that can be applied in the system consisting of a bent bar bolted at both ends through the fiberglass as shown. The diameter of the bent bar is 1/4" Ø, outside diameter of the washer is 7/8" Ø and the thickness of the fiber glass is 3/8". The working shear stress between the fiberglass and the washer is 300 psi, and the allowable bearing pressure between the washer and the fiberglass is 550 psi. Use 2 decimal places in every solved value. bent bar fiberglass washer bolt cap 7 8. 8 1/14
The column above is subjected to axial loading only. Assume the following: • E= 29000 ksi G = 10000 ksi • = 986 in4 A = 60 in? • L= 20 ft • Grade 60 steel (60 ksi yield stress) • The column is fixed at the top and pinned at the bottom Which of the following is closest to the maximum normal stress the column can support (before yielding or buckling)? 167 ksi 24 ksi 42 ksi 60 ksi
Question # 1: The composite beam is made of steel (4) bonded to brass (B) and has the cross section shown. If the allowable bending stress for the steel is (sallow) st = 180 MPa, and for the brass (sallow) br = 60 MPa, determine the maximum moment (M) that can be applied to the beam Ebr 100 GPa, Est= 200 GPa B Question # 2: Determine the maximum shear stress acting at section a-a in the beam. 150 N/m m 8000 N Bla 1.5 m 1.5 m 50 mm 50 mm 200 mm 175 mm 200 mm -B 400 mm 75 mm 600 mm 75mm
The beam AB of length L = 2m is consisted of two attached materials which are a solid aluminum %3D 9. core ( E, = 27 GPa, (tallow), = 80 MPa ) of Da = 10mm and a tubular steel (G =80 GPa, %3D %3D a (Tallow ). = 240 MPa) cover of (D3)inner = 10mm, (D,) outer = 16mm. Determine the maximum %3D %3D S. torsion T that can be applied to the beam at B without causing yielding either in the aluminum core or steel cover a St Al 10mm a (a-a Cross-section) T 16 mm
2) Find the axial stresses of menbers FD, GD, GE State if it is tensile or Compressive. 4M 3M A LE 3m G 20 RN Go KN