5V ہے اگر که + : V3 Req: _ V4! 150 - 2k 4 + + ひもでてそび

Q: Consider the following circuit and determine the following: a) The type of the circuit b) Draw the…

A: answer:  given that input voltage to primary is 50 V rms  turns ratios is Np : Ns = 4:2 =  2:1 Vs -…

Q: 15 V Si V; R R Vo O A) 9.3 V O B) 10 V C) 10.7 V O D) -10 V E) 20 V

A: Given data, The above circuit is clipper circuit. Vmax = 15 V. V = 5 V.

Q: Design a clamper circuit to perform the function indicated. Vin Vout 10 V 5.7 v Vin DESIGN Vout -10…

A: Clamper circuits

Q: Q4) Diode clamps Drive the circuit with a sine wave IK Vout of 10v amplitude and frequency of Vin…

A:

Q: 1. Design a clamper to perform the function indicated. Determine the proper value of Voc Calculate…

A: From the input waveform given, the value of input voltage is  Vin = 10V

Q: What is the fundamental frequency of the output voltage of a three-phase half-wave rectifier with a…

A: Half-wave rectifier:- By passing either the negative or positive half-cycle of the waveform and…

Q: 3. Draw the input and output waveform for the following clamper circuits if input signal is square…

A: Given data: frequency f =1 KHZ =103 HZ Peak to peak square wave v = 10 V The given circuit is shown…

Q: In a power supply, the output from a rectifier is normally connected to a load filter transformer O…

A: To get the dc output from ac input, we connect the filter circuit at the output of rectifier…

Q: Q2/ Find the output waveform for the following full wave rectifier? 10:1 D, VDi=0.3v Vms=115v 0- Rz=…

A: To charge battery from AC supply rectifier (converter) circuits are used. According to supply a…

Q: Draw the output waveform of the following Clipper’s circuits while the input is givenb below and…

A: The first circuit is  1. Negative shunt clipper with positive 5 V When the input voltage becomes…

Q: The diode voltage for a buck converter is 0.6V, the transistor voltage is 0.25V, and the input is…

A: Given: A buck converter has The diode voltage, VD=0.6 V The transistor voltage, VT=0.25 V The input…

Q: It will keep the VL voltage on the RL at 8v and will not exceed the maximum power of the zener…

A: Given  Vz = 8 V  Pzmax = 400 m Watt  Zener diode is ideal hence minimum zener current is considered…

Q: Check all the correct statements. Diodes are made from two p type semiconductors and a single n type…

A: Check all the correct statements. Diodes are made from two p type semiconductors and a single n type…

Q: 2. Draw and explain the difference between clipper circuit and clamper circuit output waveform

A:

Q: What is the difference between AND and TEST instructions? A- В I E E 123 ...

A: Logical AND is performed on two operands by using the TEST instruction. AND instrcution also…

Q: single-phase bridge rectifier has an RL load with R=15 Ohm and L = 60 mH. The ac source Vs = 100 sin…

A: It is given that: R=15 ΩL=60 mHVs=100sin377tIs1=3.9 A

Q: Find the Q point value of the diode current and the voltage gain Av in the following circuit: 700Ω…

A: Diode  It is an unidirectional electrical device, which allows current to flow only in one specific…

Q: Assuming an ideal diode model for all the diodes in the circulit below, chose the correct state…

A: The given circuit diagram is:

Q: Which circuit is changing the shape of the input Clamper circuit O Clipper circuit O None O

A: In general clipping and clamping circuits are using diodes , resistors,and capacitors They come…

Synchronous Generator

In comparison to an asynchronous generator, it is a machine where the rotor speed is equal to the rotating magnetic field produced by the stator, i.e., mechanical speed is equal to the electrical speed, thus called synchronous, and not asynchronous.

Salient Pole Rotor

Salient pole rotor includes a large number of exposed poles mounted on a magnetic wheel. The construction of a bright pole is as shown in the image on the left. The proposed poles are made of metal laminations. The rotor winding is provided on these poles and is supported by pole shoes.