55 25 10 l ø10/ 20 50 65 80

Q: how o create all parts list after the drawing ?

A: Given question: how to create all parts list after the drawing ?

Q: 12. A thermodynamic cycle is composed of the following reversible process: 1-2: Isentropic process…

A: Given1-2: isentropic process2-3: isothermal process3-1:Isobaric processworkig fluid -nitrogen…

Q: - Consider the four – bar mechanism in Fig. 1 with a velocity VA= 9.14 m/s, determine : A) all…

A: Angular velocity is the rotational velocity of a body. It is equal to the angular distance covered…

Q: Q-3: The bulk head AD is subjected to both water and soil-backfill pressures. Assuming AD is…

A:

Q: (a) An aeroplane flying at 240 km/h turns towards the left and completes a quarter circle of 60m…

A: given; velocity(V)=240km/h                   =66.67m/smaking radius (r)=60mmass of propeller…

Q: 10. A beam ABCDE with AB = 1 m, BC = 2 m, CD = 2 m and. DE = 1 m is supported by a hinge at B and…

A:

Q: Member ABC has a mass of 2.4 kg and is attached to a pin support at B. A 0.8 kg sphere D strikes the…

A: Given : To find : Negligible impulse force

Q: 59. A mass m is mounted betwe two springs with constants k, and k2, as shown in Fig. 13.32. Show…

A: As per the policy of the bartleby I can answer 1st question only. All the questions are different to…

Q: Consider a large, helium-filled party balloon with a volume of 1.23 ft^3. The lifting force on the…

A:

Q: 1.11 The vacuum pressure of a tank is given to be 40 kPa. If the atmospheric pressure is 95 kPa,…

A: GivenP=40 kPa   vacuumPatm=95kPa

Q: A o 25 mm hole is pierced in a t = 2.5 mm thick steel sheet having shear strength t = 350 MPa. If…

A:

Q: Answer the no.6 question (tick one)

A: (6) The torque developed in Pelton wheel is given as, Here, ? is the density of water, A is the…

Q: 3. Dry saturated steam at 200 bar expands isothermally and reversibly to a pressure of 10 bar.…

A: Given Data State 1: 200 bar,dry saturated State 2: 10 bar Isothermal expansion process

Q: P1. Consider a particle in a box of length L in which the potential at the bottom of the box is…

A:

Q: P1-4. Determine the internal normal force at section A if the rod is subjected to the external…

A:

Q: An undamped spring mass system has a mass of 10 kg and a spring stiffness of 2250 N/m. It is excited…

A:

Q: A moving car accelerates uniformly from 75 m/s at time t=0 s to 135 m/s at t = 10s. Define. (i) Car…

A:

Q: 55 45 70 75 40 10 Omega rad/s (o) Fig. 2a Data pertaining to X1/F1 can be found in BeachBoard file…

A: As per Bartleby terms and conditions we are restricted to solve only one question at a time . yor…

Q: A solid sphere (I = mr?) starts from rest at a height h and rolls down an incline of angle 0 without…

A: Given data: The inertia of the sphere is I=25mr2 The relation linear velocity and angular velocity…

Q: Need answer please

A:

Q: Determine the polar moment of inertia about point O of the shaded area shown. 30 30 30-X 20 45° 45…

A:

Q: A nuclear power plant has a rated capacity of 200 MW electrical power. The core contains 50 tons of…

A:

Q: In which plane is the centroid of the following figure most likely located? yz-plane xy-plane…

A:

Q: Q.2. An engine uses a high capacity to flow coolant around the engine and through the To assist the…

A: Given:- The working of the cooling system of the engine To find:- The blanks for the above process…

Q: 2. Antifreeze is added to car radiators to prevent the water in the radiators from both freezing and…

A: a. Yes, Antifreeze maybe a tinted fluid merely put (together with water) in your radiator to…

Q: For the beam shown below: - Draw the free body diagram showing the reactions for each type of…

A:

Q: Determine the displacement of joint A if the load has a mass of 500 kg. Element AB has a length of…

A:

Q: A body having a cylindrical shape of length equals to 1.9 m and diameter equals to 400 mm is inside…

A: Lumped Capacitance method is a method of heat transfer analysis, where a spatially uniform solid…

Q: Q3: A cube of edge 24mm is resting on the top of a frustum of cone of base diameter 60mm and top…

A: Q3. Given data:-  Cube edge = 24 mm Cone base diameter = 60mm Cone top diameter = 40mm  Axis height…

Q: How to draw 4/5 × 2/3 on a model

A: A mixed fraction is a fraction that has both a quotient and a remainder. 2 1/3, for…

Q: 2. A 1-m' rigid volume contains water at 90°C with a quality of 0.B. Determine the final temperature…

A:

Q: The figure below shows a turbine with an inlet pipe and a draft tube. If the efficiency of the…

A:

Q: A power screw has a pitch (p) of 10 mm/revolution. It is driven by a stepper motor that has a…

A: Required Information:

Q: An airplane is flying at 1500m witha speed of 45 m/s. What is the stagnation pressure measured in…

A: Write down the given value using suitable variables. Here H1 signifies the initial height of the…

Q: Consider a 5-m-long, 5-m-wide, and 1.5-m-high above-ground swimming pool that is filled with water…

A:

Q: A rod consisting of two cylindrical portions AB and BC is restrained at both ends. Portion AB is…

A:

Q: 13. If there are four reversible processes given: Isochoric, Isopiestic, Isothermal, and Isentropic.…

A: Carnot cycle: The Carnot cycle consist of four reversible processes: 1. Isothermal Expansions 2.…

Q: Example 11.18. A rod of circular section is subjected to a shearing force on a plane perpendicular…

A: