5/42 A variable-speed belt drive consists of the two pulleys, each of which is constructed of two cones whic turn as a unit but are capable of being drawn together or separated so as to change the effective radius of the pulley. If the angular velocity w, of pulley 1 is constant, determine the expression for the angular acceleration a2 = wz of pulley 2 in terms of the rates of change r1 and r2 of the effective radii. !! b1 b2 PROBLEM 5/42 Answer

5/42 A variable-speed belt drive consists of the two pulleys, each of which is constructed of two cones whic turn as a unit but are capable of being drawn together or separated so as to change the effective radius of the pulley. If the angular velocity w, of pulley 1 is constant, determine the expression for the angular acceleration a2 = wz of pulley 2 in terms of the rates of change r1 and r2 of the effective radii. !! b1 b2 PROBLEM 5/42 Answer

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Three spur gears R,S and T are mounted on parallel shafts ,such that R meshes with S,and S meshes with T gear wheel.R has 10 teeth ,while gear wheels S and T have 60 and 40 teeth respectively .Determine the speeds of S and T if R rotates at 130 rev/min and also indicates that the speed of gear T is independent of the number of teeth on gear S
Determine if for the position shown there is a Coriolis acceleration at the pin/pin a. If your answer is affirmative, draw the direction of the Coriolis vector on the mechanism.
2. HANDWRITTEN - Specifications: 3 O N Link AB BC CD AD AE DE EF BO 60⁰ Length (ft) 1.8 3.75 3.75 4.5 4.35 6.0 11.1 E 5 EF = 11.1 F Determine the angular acceleration of link 5 if the drag-link mechanism is turning CW at the rate of 130rpm.
B4
B7
5/7 The rectangular plate is rotating about its corner axis through O with a constant angular velocity = 10 rad/s. Determine the magnitudes of the velocity v and acceleration a of the corner A by (a) using the scalar relations and (b) using the vector relations. 400 mm 300 mm 2 Problem 5/7 B
The large (1) wheel in figure 1 is rotating around the fixed axis passing through point O with an angular speed w1 = 4rad / sec. The OA crank rotates around the fixed axis from point O with an angular speed woa = 2rad / sec. Find the center of velocity P and angular velocity w2 of the small (2) impellers moving in a plane. Also, if (OK) = R = 60cm, (AB) = r = 20cm, (AC) = 12cm, (AE) = 11cm, (2) find the velocities of the A, B, C, E and K points of the impeller and form Table 3. . Also show the velocity vectors of the points A, B, C, E and K on the figure.
Determine the velocity of rod R for 0 T/2 rad in the cam C if the cam rotates with a constant angular velocity w = 10 rad/s . The pin connection at O does not cause an interference with the motion of A on C. Enter the velocity of R in m/s in the box below. Assume positive to the left, as shown in the figure. ri = 1 m, r2 = 0.15 m. Enter the answer in m/s in the box below. C www R
2
If the operator initially pushes the pedals at 20 rev/min and then initiates an angular acceleration of 6 rev/min2, determine the angular speed of the flywheel F (in rev/min) after the pedal has rotated 2 revolutions. Note that the pedal arm is connected to the chain plate A, which, when turning, drives the tethered pulley B through a coupling gear D. The belt wraps around the tethered pulley and then drives pulley E and the fixed flywheel. . B D "A = 125 mm "D = 20 mm "B = 175 mm "E = 30 mm F
In the figure, Pulley A, rotating at 20 rad/s, controls the motion of Pulley B. The motor of pulley A is cut off, and friction eventually brings the pulleys to a stop with an angular acceleration of α = -2.5t rad/s2. If there is no slippage, determine: a. The angular velocity of B with respect to time b. The angular displacement of B during the deceleration c. The acceleration of point C with respect to time
the pinion A of the hoist motor drives gear B, which is attached to the hoisting drum. The load L is lifted from its rest position and acquires an upward velocity of 4ft/sec in a vertical rise of 5 ft with constant accelerations. As the load passes the position, compute the acceleration of point 6 on the cable in contract with the drum.