5/101 Determine the reactions at A and B for the beam subjected to a combination of distributed and point loads. 1.2 m Ans. A, 750 N, A, 3.07 0.6 m -2 kN/m = 3.07 kN, By = 1.224 kN kN, By 1.2 m 1.8 m 1.5 kN 30° 1.2 m OB

Q: Define CMM.

A:

Q: 20 40 t. 20 40 30 40 20 to 30

A: Gross area of the column =area of concrete + area of reinforcementGross area of the first column…

Q: How many "varas" are there in a single ruler measurement?

A: A single ruler is the standard ruler which has measurements given in inches or mm. It is used to…

Q: show the integration process

A: To show the integration process

Q: Define Decimeter.

A: Decimeter: It is a length unit in a metric system. which is equal to a tenth of a meter.

Q: What is Structural Plan?

A: A structural plan is a plan used as a framework to take up the land development or renovation of an…

Q: What are the characteristics of ordinal level measurement scale variables?

A: Data provided :  Ordinal level measurement scale variables    To determine : The characteristics of…

Q: how did you get 1.5 for the first part

A: In the original question it is stated that Vmax=2 Vmin In the solution, the following is given.…

Q: Define integer ambiguities.

A: Answer The integer ambiguities are used in GPS & GNSS surveys.

Q: What are Cole values

A: Solution: COLE stands for The Coefficient of linear Extensibility.  It is used to measures the soil…

Q: What is a box model? Give the equation to represent box model.

A: The Urban air quality models has been called box models. The Figure is a schematic graph of a box…

Q: 10 25k 10'

A: The below cantilever beam is given;

Q: where did you get 6?

A: 6 is the loading intensity at B.

Q: Find KN derivation Y = K m²³

A: We have to prove that the unit of unit weight is kN/m3.

Q: what letter are those?

A: According to me  This symbol represent bending moment at any distance ( x ) in a beam.

Q: what is america door panel and it size

A: Solution: The most common front sizes of the door in American houses are 36 inches wide and 80…

Q: Define the term Index Properties.

A: The index properties are the soil properties which help to identify and classify soil. These…

Q: What is the difference between interval and ratio level measurement scales?

A:

Q: What is Landsat and name 2 Civil Engineering Applications can it be used for?

A:

Q: Renolds number, define it?

A:

Q: How are units converted using dimensional analysis?

A:

Q: 3. Name any two-pattern material.

A: Introduction- There are several types of material found in nature. Some materials form certain…

Q: Explain the Modified Mercalli scale.

A: The effect caused on the surface of the earth due to an earthquake is known as the intensity of the…

Q: Define Spencer Charts.

A: Spencer defines the factor of safety as the available shear strength quotient divided by mobilized…

Q: What is sumps?

A: Sump collects building up underground water so that it can be pumped aside from a finished building…

Q: * To draw an arc angle between two intersecting lines Fillet O Block O Trim Chamfer O If we want to…

A:

Q: With the aid of an illustration, describe two methods by which areas bounded by irregular lines can…

A: Areas bounded  by irregular lines can be found by using midoridnate rule , trapezoidal method ,…

Q: Is "Object-Oriented" a term that may be used without any problems? The creation of software that…

A: "Object-Oriented" is a widely accepted and established term in software development that refers to…

Q: You are appointed as an officer of Occupational Safety to investigate the incident happened during…

A: Officer of Occupational Safety is responsible for 1) Enforcing safety policies, 2) Conducting audits…

Q: Differentiate initial and boundary value problems.

A: Both type of problems are similar to each other except for that boundary value problem have…

Q: How is the dimension paper used to compile an accurate Bill of Quantities??

A: Dimension paper is used in taking off which refers to the process which identifies elements of…

Q: Define Relative precision.

A: Relative precision:

Q: What are Quantity Variations?

A:

Q: What is Micropiles?

A: - A Micropile is a type of friction pile having diameter less than equal to 305 mm which can be…

Q: Define a logic loop.

A: The loop means a continuous order of formations which can repeat the work until a certain…

Q: Define Relative Density.

A: Relative density or specific gravity:

Q: express each measurement in feet.108 inches

A:

Q: Define the following words Tesserae Kline  Klismos Chai

A: These three terms give various elements that are important in design and art. Learning these will…

Equilibrium and Support Reactions

Civil engineers deal with structures that are composed of several members connected or with individual members such as beams and columns. To analyze such structures, the condition of statics must be applied. Under the static condition, the members are considered to be in equilibrium under the action of forces, that is, the members are assumed to be having negligible velocity.