1:32 PMP © 53%SITUATION:500 mm x 500 mm column carries aDead Load of 1430 kN and a Live Loadof 700 kN. The allowable soil pressure is270 kPa, the dimension of footing is 3 mx 3 m, and there is a 0.70 m soil at thetop of the footing with 18.1 kN/m³ unitweight. The footing is reinforced with18-25 mm bars both ways, the totaldepth of the footing is 635 mm. Thematerial properties for the footing are asfollows, fc' = 20.7 MPa, fy = 276.5 MPa.%3DWhat is the actual net soil pressure?O242.614 kPaO263.76 kPaO224.416 kPaONone of TheseO236.67 kPaDetermine the wide beam shear stressat ultimate loads.

Dead load = 1430 KN Live load = 700 KN Dimension of footing = 3×3 m In the calculation of net…

Answered: 500 mm x 500 mm column carries a Dead…

Engineering

Civil Engineering

500 mm x 500 mm column carries a Dead Load of 1430 kN and a Live Load

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: ISMB 200 rolled steel joist is used as column is 5 m long with one end fixed and other being hinged.…

A: Given data- ISMB 200 rolled steel joist-Column length L=5 mOne end fixed and other…

Q: A simply supported timber beam with length L-5m carries a uniformly distributed load w - 8 kN/m.…

A: Given data in question Span member length UDL Cross section To find out Bending stress in…

Q: used in a transmission not restrained in directio N/mm?.

Q: The beam shown in the figure is a two-span beam with a pin (hinge) in the center of the left span,…

A: We need to find the maximum Moment on the beam and compare it with the W 12 x 79 beam Moment…

Q: A mild steel column is hollow and circular in cross-section with an external diameter of 350mm and…

A: Given: The external diameter is 350 mm. The internal diameter is 300 mm. The load is 2000 kN. The…

Q: Load A (Ib.) D 15 ft M 15 ft K 20 ft 20 ft 20 ft 20 ft- 6000 lb 8000 lb

Q: A solid circular steel column is to be design to carry an axial load of 620 kN. If the allowable…

Q: A typical rigid bar AB of the length 5m for a cantilever type car shed as shown in figure is hinged…

A: The given data is as follows: Length of bar AB=5 mDiameter of steel wires=3 cmDistance of wires from…

Q: The frame shown is subjected to lateral loads as shown. Supports S, T, U, V, W, Z are rigid…

A: In portal method, 1. Hinges are assumed at middle of each member. 2. frame is cut at different…

Q: Determine the maximum safe vertical load W that can be supported by the tripod shown in the figure…

Q: Design the amount of reinforcement for a maximum positive moment in beam DEF. Present your answer in…

A: Given- A Reinforced concrete beams 300 mm wide and 500 mm deep are spaced 2.5 m on centers. The…

Q: An A-36 steel column has a length of 15 ft and is pinned at both ends. If the cross-sectional area…

A: To Determine Maximum axial load that can be applied before any type of failure of the column, P

Q: An I-section shown in Fig. is simply supported over a span of 12 m. If the maximum permissible…

Q: Determine the maximum negative bending moments at point B due to a concentrated live loads of 50 kn…

Q: A stainless steel tube with an outside diameter of 66 mm and a wall thickness of 5 mm is used as a…

Q: nt of forklift: 2,000 lb nt of load: 900 lb is at B are free to roll. mine the reactions a

Q: 1- 2- 3- A hollow cast-iron cylinder 4m long, with 300mm outer diameter, and thickness of metal 50…

Q: A 7.0 m simply supported rectangular beam has a width of 450 mm and a depth of 850 mm. Supports, in…

Q: The concrete girders shown in the photo of the passenger car parking garage span 30 ft and are 15 ft…

A: Solution: Given: LL = 50 lb/ft2 L = 30 ft B = 15 ft t = 5 in = 0.416 ft unit weight of concrete =…

Q: e loads and dead loads act in a

A: To find: We have to find whether the given statement is true or false. Given: Live loads and dead…

Q: An A36 W 12 x 65 column section is 8 m long, pinned at each end and has an additional support in the…

Q: A W360X72 column is pinned at both ends. The length of column (L) = 3.5m and modulus of elasticity…

A: We have to find out the critical stress when critical laod is applied and given section is W360X72.

Q: A steel column carries an axial load of 801 kN and a moment of 71 kN-m at the top and moment at the…

A: A steel column carries an axial load of 801 kN and a moment of 71 kN-m at the top and moment at the…

Q: A Assignment 1 @p=1.5 k/ft @=2.0 k/ft 20 ft f=5,000 psi f₂ = 60,000 psi Including beam weight B PD=5…

Q: For the floor plan shown below, a = 20 ft, b = 30 ft, and c = 4 ft. Each floor of the regular…

Q: Question No. 12: (a) Explain the buckling of columns in detail. (b) Define factor of safety. Explain…

A: Buckling of Columns:Buckling of columns refers to the instability and failure of slender vertical…

Q: Design a square tied column to support an unfactored axial dead load of 900kN and live load of 1240…

A: We need to design the column for the given specifications.

Q: An aluminum strut 2.00m long has a rectangular section 50mm by 30mm. A bolt through each end secures…

Q: The linkage below is made using two A992 steel rods, each having a circular cross section. 10klp.…

A: This question is related to Strength of Material. We calculate Diameter of Bar AB and BC using…

Q: The beam shown in the figure is a two-span beam with a pin (hinge) in the center of the left span,…

A: We need to find the maximum Moment on the beam and compare it with the W 12 x 79 beam Moment…

Q: Determine the reaction forces for beams B-1, B-2, and B-3. Column A Column B Girder G-1 open Girder…

Q: A steel rod 30 mm in diameter and 800 mm long has an allowable elongation not to exceed 1.5 mm, find…

Q: 1.The end moments of the beam shown due to service loads are tabulated below. Determine the design…

A: Dead loads, otherwise called long-lasting or static burdens, are those prevalent connected with the…

Q: a) Find the factored critical moments based on ACI moment coefficients. b) Find Pmax c) Find pmin…

A: "Since you have posted a question with multiple sub-parts, the first three sub-parts will be only…

Q: 6. A reinforced concrete column has cross sectional dimensions of 400mm x 400mm. The column is…

A: To design the reinforced concrete column according to the ACI (American Concrete Institute) code, we…

Q: I

Q: 23. Live loads and dead loads act in a horizontal direction. a) False b) True

A: Statement: Live loads and dead loads act in a horizontal direction. To calculate: above statement is…

Q: A simply supported laterally/restrained beam carries the working loads shown select a considering a…

A: Given: Span of the beam = 6 m Uniformly distributed loads: Dead load = 8 kN/m Live load = 10 kN/m…

Q: Q2: A simply supported beam AB has a length of 3 m and carries distributed load which varies in…

Q: The total average load is 60 lbs/ft³. Calculate the reactions in Beam D Column 1| Beam A Column 2…

A: Given: Average dead load and live load = 60 psf

Concept explainers

Material Properties

Construction in civil engineering demands high strength, durability, and longevity. These targets can be achieved by better design and analysis, along with the correct choice of materials. Different materials have different properties and hence, they respond and performs differently under the various condition of external loadings. It is therefore a critical task of an engineer to select the right material based on the property that the material is supposed to function in real-time. When speaking about the property, there are different categories of material properties like chemical property, physical property, mechanical property, electrical property, magnetic property, thermal property, etc. These material properties form the basis of material selection in various applications.

Question

1:32 PM
P © 53%
SITUATION:
500 mm x 500 mm column carries a
Dead Load of 1430 kN and a Live Load
of 700 kN. The allowable soil pressure is
270 kPa, the dimension of footing is 3 m
x 3 m, and there is a 0.70 m soil at the
top of the footing with 18.1 kN/m³ unit
weight. The footing is reinforced with
18-25 mm bars both ways, the total
depth of the footing is 635 mm. The
material properties for the footing are as
follows, fc' = 20.7 MPa, fy = 276.5 MPa.
%3D
What is the actual net soil pressure?
O242.614 kPa
O263.76 kPa
O224.416 kPa
ONone of These
O236.67 kPa
Determine the wide beam shear stress
at ultimate loads.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Calculation

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A 3m-LONG CANTILEVER BEAM IS CARRYING A UNIFORM DEADLOAD OF 20 kN/m (EXCLUDING SELFWEIGHT OF THE BEAM), AND A LIVE LOAD OF 15 kN/m. OTHER GIVEN: fc = 27.5 MPa fy = 414 MPa b = 300mm h = 600mm diameter of main reinforcements, db = 25mm diameter of transverse reinforcements, ds = 12mm use clear concrete cover of 45mm unit weight of concrete is 25kN/m3 Solve for the following: a. Reactions at the fixed support. b. Maximum FACTORED moment of the beam, Mu c. Effective depth of the beam d. As required e. No. of 25mm reinforcements required to resist Mu f. Spacing of stirrups at the critical location (d from face of the support) - use manual calculations, show your solutions.
learn Determine the reaction forces for beams B-1, B-2, and B-3. Column A Column B Girder G-1 open Girder G-2 L1 L1 L1 • Live load = 30 psf • Dead load: (1) Slab = 50 psf, (2) Deck = 5 psf, (3) Mechanical equipment = 13 psf, (4) Suspended ceiling = 8 psf, (5) Beam = 25 Ib/ft, (6) Girder 35 lb/ft • Beam and Girder spacing: : (1) L1 = 14 ft, (2) L2 = 10 ft, (3) L3 = 10 ft Please round to the nearest one. Reaction force for Beam B-1 (one side only) = Ibs Reaction force for Beam B-2 (one side only) = Ibs Reaction force for Beam B-3 (open side) = Ibs Reaction force for Beam B-3 (Girder G-1 side) = Ibs MacBook Air II F8 F1 F2 F3 F4 F5 F6 F7 $ % & * 2 3 4 5 6 7 8 Beam B-1 Beam B-2 Beam B-3 Beam B-4 L3 L2
A concrete beam has a cross sectional area of 275mmwidth and 150mm height for the upper flange. While thelower flange has 450mm width with a 150mm height. If theflange has length of 225mm while 200mm width,determine the centroid and the moment of inertia of thegiven structure. answer this ASAP. Please thank you
A steel column carries an axial load of 801 kN and a moment of 71 kN-m at the top and moment at the bottom which is only70% of the moment at thetop. The two moments are in opposite direction and applied about the x-axis and the steel section has the following properties:A = 13159 mm2ry = 109 mmry = 94 mmSx = 1200 x 103 mm3K= 1.0L= 3.6 mE= 200,000 MpaFy = 248 MpaUse NSCP specification for compressive stress and Fb =148 Mpa.Determine the Allowable Compressive Stress.
A 6m steel wire hanging on one end has a weight of W, it supports a load of 243 kN, determine the required diameter if the elongation would not exceed 1.69 mm, Assume E = 2 GPa.
a reinforced concrete column of 300mm dia contains 4 bars of 22mm dia. find the total load, the column can carry, if the stress in steel and concrete is 50MPa and 3MPa respectively.
Question 17
Need it asap pls
A steel column carries an axial load of 785 kN and a moment of 72 kN-m at the top and moment at the bottom which is only70% of the moment at the top. The two moments are in opposite direction and applied about the x-axis and the steel section has the following properties: A = 12818 mm2rx =109 mmry= 94 mmSx = 1200 x 103 mm3K= 1.0L= 3.6 mE = 200,000 MpaFy = 248 MpaUse NSCP specification for compressive stress and Fb =148 Mpa. Questions:From the Interaction Formula, compute the interaction value. Assume that the column is braced against joint translation (sidesway).
A simply supported bseam of a beam and slab system, rests on a support of width 450 mm. The clear span of the beam is 10.0 m., The thickness of the slab is 120 mm. The depth of the beam below the slab is 480 mm and the width of the beam is 250 mm. The beam is reinforced with one row of 32 mm diameter steel rods. The total load including the super imposed dead load, live load and its own weight is 25.0 kN/m at service stage. Compute the maximum nominal design shear stress in the concrete.
a uniform load w across its full length. Use this beam to respond to problems 4 through 8. 4. The support reaction at 8 equals (a) aw (b) 2w (c) w/2 (d) 2aw (e) None of these