50 kN 15 kN/m 150 kN m 6 m 3 m 3 m 1. The vertical reaction at A is a. 45.50kN b. 55.60kN C. 72.50KN d. 67.50kN 2. The vertical reaction at D is a. 45.50kN b. 55.60kN c. 72.50kN d. 67.50kN

Q: Determine the slope at B and the displacement at poust for for the beam IDm 10m 10m (0m

A:

Q: E,I # Constant. F7な ラ ->

A: Given data:

Q: Determine the reaction at the support B. 500 N 400 N 0.5 m 2 m 2 m

A:

Q: 12K A 81 81 84 8K 6k 8K

A: Introduction: For solving reactions acting on any structure we have to follow three equilibrium…

Q: Determine the reactions at A and B for the steel bar and loading shown, assuming a close fit at both…

A: Given data:- Conditions given-Remove restriction at A and solve for the reactions Below bar figure…

Q: Determine the reactions at rigid supports A and B. A B →10 kN 1 m 2 m

A: Following is the given rod between two rigid supports:

Q: Determine the components of the reactions for the beam

A:

Q: Determine the reactions of the structure, given that X= 7 ft. 10 kips F ———X—₁▬▬▬▬▬▬5²- The…

A: Given data:- X = 7 ft.

Q: 30 kN/m B A 10 m

A: Using equilibrium equation

Q: Determine the reaction in the support of the beam loaded and supported as shown: 5 kN/m 5 kN/m 40 kN…

A:

Q: A beam AB is supported by a pin at A and a rocker at B. Note that while the pin at A is in the…

A: Given data in question  Loads Span member length  Angle To find out  Reactions

Q: Solve for all reactions at A and B

A:

Q: 2. Portions AB and CD have flexural rigidity EI, and portion BC has flexural rigidity 3EI. Determine…

A: P = 30kips w = 1kips/ft [Note :equation (i) & (ii) has been added and equated to zero, due to…

Q: X= 482  Y=82 C=2 SHOW COMPLETE

A: X=482 Y=82 C=2

Q: Determine the vertical reaction at D, A, force in FBC, and force in FGC

A: Consider the figure,

Q: Problem 1. The wooden beam is supported by a pin at A and the two-force strut BC. Draw a complete…

A:

Q: Determine the horizontal and vertical components of reaction on themember at the pin A, and the…

A: Consider the following free body diagram:

Q: Required: Draw the free-body diagram needed to determine the reactions at supports A and B. Find…

A: The free body diagram of the beam,

Q: B 30° 8. Determine the reaction at B. (Ib) 9. Determine the horizontal reaction at A. (Ib) 10.…

A:

Q: Determine the reaction at the support B. 500 N 400 N 0,5 m 2 m 2 m

A: Since the system is in equilibrium, hence Net force in x and y directions are zero also, net moment…

Q: Determine the components of the reactions for the beam

A:

Q: Solve the support reaction at A. 6 ft A B 8 ft 8 ft E 8 ft 6 ft 30 kips C

A:

Q: B Y (N/m) 30° 0.75 m Y (N-m) - 1.5 m 1. Determine the resultant force of the triangular loading. (N)…

A: Given data,  Y = 25 To find out the resultant of triangular loading, reaction in A and B

Q: 2) Determine the force in member BD of the structure components shown. Also determine the of the…

A: Given : Determine the force in member BD and also determine the component of reaction at C ?

Q: A beam AB is supported by a pin at A and a rocker at B. Note that while the pin at A is in the…

A: Given that : AB is supported by a pin at A and a rocker at B. the pin at A is in the center if the…

Q: State the degree of indeterminacy of the structures(1.2,3,4,5. If the structure is unstable input…

A:

Q: Determine the reaction at the support B. 500 N 400 N 0.5 m 2 m 2 т

A:

Q: The given truss shown is supporting the load R = 108.8 kN on B. The truss has roller support at D…

A: Given: Required: Reaction at D Horizontal reaction at E Vertical reaction at E Note: As per…

Q: Determine the vertical component of the reaction at A, Av. Also, find out the reaction at support F,…

A:

Q: Determine the reactions at A. 5 kip 10 ft 10 ft + 10 ft # 10 ft AV 10 kip 10ft - Skip - 10 kip 10…

A: Given:Required:Support reaction at A

Q: Determine the reactions at A and C when (a) a =0, (b) a =30 degrees. 800 mm C 300 N 200 mm 300 N 200…

A:

Q: 2000 N/m 1500 N/m 1000 N/m - A B 0. 3m 0. Sm 0. 2m 0. 3m 0.15m 0.15m

A:

Q: Solve for the reactions

A: Given Data Determined the support reaction.  Let's solve using Moment Distribution Method.

Q: Determine the vertical component of the reaction D, at the pin support D

A:

Q: Solve for the reaction at D.

A:

Matrix Algebra for Structural analysis

Structural analysis is a process in which the effects of different loads and internal forces, acting on structures and their elements are determined. This method of analysis is effective in detecting the failure loads of the structural elements and the design can be altered before commencing the construction process, which ensures proper strength and safety of the structures.