5.9 From the data given below, calculate the power required to drive the compressor and stage air angles for an axial flow compressor. Stagnation temperature at the inlet: Overall pressure ratio: Isentropic efficiency of the compressor: 0.88 Mean blade speed: Axial velocity: Degree of reaction: 288 K 4 170 m/s 120 m/s 0.5 (639.4 kW, B, = 77.8°, B, = – 72.69°)

5.9 From the data given below, calculate the power required to drive the compressor and stage air angles for an axial flow compressor. Stagnation temperature at the inlet: Overall pressure ratio: Isentropic efficiency of the compressor: 0.88 Mean blade speed: Axial velocity: Degree of reaction: 288 K 4 170 m/s 120 m/s 0.5 (639.4 kW, B, = 77.8°, B, = – 72.69°)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Send the correct solution with diagrams
I need the answer as soon as possible
5. Combustion gases with k=1.35, Cp=1107 J/(kg.K) and R= 287 J/(kg.K) flow at stagnation pressure and stagnation temperature of 390kPa and 1150 K respectively, flow through a 90° IFR turbine to an exit static pressure of 100 kPa. The total to static efficiency is 80% and the flow leaves the stator choked (Mach Number=1). The relative velocity at the inlet to the rotor is radial and the flow leaves the turbine without a swirl. Find (a) the work delivered per unit flow rate, (b) the impeller tip velocity and (c) the flow angle at the inlet to the rotor. :-
A single stage single acting air compressor with runs at speed 600 rpm. It has a polytropic index of 1,26. The induced volume flow rate is 0,72 cubic meters per min and the air must be delivered at a pressure of 707 KPa. The free air conditions are 101,3 KPa and 15 degrees Celsius. The clearance volume is 7,6 % of the stroke volume and the stroke /bore ratio is 1,6/1. Calculate 1.The stroke volume of the cylinder in cubic meters to 5 decimal places. 2.The bore of the piston in meter to 4 decimal places.
8. A turbine passes 67.5 kg/h of steam at 200 km/h at 8 MPa and leaves at 0.5 MPa as wet steam with a speed of 90 km/h and a specific volume of 0.189 m3/kg. d. What must be the steam input conditions (T,H) to turn on a device that consumes 30 kW? and. What is the mass and volumetric flow rate of the water at the outlet? F. What is the input and output area?
: A single stage axial flow compressor with isentropic efficiency of 80%. The comperessor delivers 20 kg/s of air at a rotational speed of 9000 rpm, the stagnation temperature rise is 20 K and the axial velocity is 150 m/s, the mean blade speed is 180 m/s and λ=0.94. The degree of reaction is 50% at mean radius. Take the ambient conditions as 1 bar and 288 K. Find 1) Blade and air angles ( α1, α2, β1, and β2) at mean radius 2) Stage pressure ratio 3) Blade heigh
Please indicate a diagram. Thanks
There are two turbine stages with a reheater in between, as shown below and the following conditions are provided. Assume the mass flow rate of air = 1 Kg/s. Turbine stage 1 Stream 1 2 3 4 Reheat combustor P (kPa) T (K) 1200 350 350 100 1200 1200 3 Turbine stage 2 h (kJ/kg) W cycle • Determine the total work developed, which is the sum of the work developed by the first stage and the work developed in the second stage. • Determine the heat added in the reheater. • If the reheat is turned off, streams 2 and 3 no longer exist and we go directly from 1 to a new state at stream 4. What is h4 and what is the work generated in the turbine in this case?
5.16. For a centrifugal compressor rotating at 2500 rpm, find the compression ratio for the following specifications. T = 300 K; 79 (volumetric flow rate)=1.25 m³/s and t (the thickness of the flow section at the exit) = 0.15 m. = 0.85; r, = 0.55; ra = 0.015; B, 60°,
Q - The rotor of an impulse turbine is 60 cm diameter and runs at 9,600 r.p.m. The nozzles are at 20° to the plane of the wheel, and the steam leaves them at 600 m/sec. The blades outlet angle are 30° and the friction factor is 0.8. Calculate the power developed per kg of steam per second and the diagram efficiency.
Combustion gases with k=1.35, Cp =1107 J/(kg.K) and R= 287 J/(kg.K) flow at stagnation pressure and stagnation temperature of 390kPa and 1150 K respectively, flow through a 90o IFR turbine to an exit static pressure of 100 kPa. The total to static efficiency is 80% and the flow leaves the stator choked (Mach Number=1). The relative velocity at the inlet to the rotor is radial and the flow leaves the turbine without a swirl. Find (a) the work delivered per unit flow rate, (b) the impeller tip velocity and (c) the flow angle at the inlet to the rotor.
Superheated steam at 40 bar absolute and 500°C flows at a rate of 250 kg/min to an adiabaticturbine, where it expands to 5 bar. The turbine develops 1500 kW. From the turbine thesteam flows to a heater, where it is reheated isobarically to its initial temperature. Neglectkinetic energy changes.(a) Write an energy balance on the turbine and use it to determine the outlet streamtemperature.(b) Write an energy balance on the heater and use it to determine the required input (kW) tothe steam.(c) Verify that an overall energy balance on the two-unit process is satisfied.(d) Suppose the turbine inlet and outlet pipes both have diameters of 0.5 meter. Show that itis reasonable to neglect the change in kinetic energy for this unit.