5.6 A beam with the square cross section shown carries a maximum bendingmoment of 8000 lb - ft. Determine the maximum bending stress if the beam is firstoriented as shown in (a), and then as shown in (b). For both orientations, the z-axisis the neutral axis; that is, the axis about which the bending moment acts.6 in.6 in.6 in.(a)(b)6 in.

Bending moment, M=8000lbftSide of square, a=6in

5.6 A beam with the square cross section shown carries a maximum bending moment of 8000 lb - ft. Determine the maximum bending stress if the bcam is first oriented as shown in (a), and then as shown in (b). For both orientations, the z-axis is the neutral axis; that is, the axis about which the bending moment acts. 6 in. 6 in. 6 in 6 in.

5.6 A beam with the square cross section shown carries a maximum bending moment of 8000 lb - ft. Determine the maximum bending stress if the bcam is first oriented as shown in (a), and then as shown in (b). For both orientations, the z-axis is the neutral axis; that is, the axis about which the bending moment acts. 6 in. 6 in. 6 in 6 in.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Solve the bending stress about the y-axis at points A and B. Indicate if the stress is in tension or compression. 200kN m B 200mm ▶44 15mm 200mm A 400mm 20mm
For the beam shown below, use your preferred method and determine:a. The reactions at the supports (Ray, Rbx, Rby). b. The shear force diagram. c. The bending moment diagram.
6
The horizontal rigid beam ABCD is supported by vertical bars BE and CF and is loaded by vertical forces P₁ = 400 kN and P₂ = 360 kN acting at points A and D, respectively (see figure). Bars BE and CF are made of steel (E = 200 GPa) and have cross-sectional areas ABE = 11,000 mm², Acf-9280 mm² and bars are shown in the figure. 1.5 m P₁ = 400 kN E A B 1.5 m A A 2.1 m A D P, 360 kN 2.4 m F 0.6 m Determine the vertical displacements 8 and 8p of points A and D, respectively.
The 100 N block hits the simply supported beam at its mid span after a drop of 10mm as shown in the figure, consider flexural rigidity of the beam as 1728N-m². The dynamic deflection (in mm) at mid span is 100N W 0.6m 10mm 0.6m
Asap pls
A pin-jointed 2-D truss is loaded with a vertical load of 10 kN as shown in figure. The crosssectional area of the horizontal member is 150 mm² and cross-section areas of the members AC and BC are 200 mm² each. Modulus of elasticity of the truss material is 200 kN/mm². The magnitude of horizontal displacement (in mm, round off to two decimal places) of joint Cis A -6m 10 KN 5 m 4.5 m
Compute the maximum tensile and comprsive stresses devloped in the beam that is loaded and has the cross-sectional properties shown in fig 8 KN 120 mm 10 KN/m ΝΑ A 1=20 x10 6 mm4 4m B C 1m 50 mm
stresses in beams 3.
Figure 6 demonstrates a cantilever shaft is fixed at A and free to rotate at its right end at F. The shaft is made from steel and consists of variable diameters. for segment CF, consists of a hollow shaft and has an inner diameter of 10mm. A torque of 150 Nm, 335 Nm, and 80 Nm is applied at B, D, and E respectively. The modulus of rigidity of shafts is 95GPa. i) determine the torsion for each segment ii) show the torsion diagram for shaft iii) determine the largest shear stress developed in the shaft iv) calculate the twist of the angle at points D and F for the shaft.
Please solve it fast. Within 20-30min
Q.2) For the truss shown in figure below, determine the forces in A 2000 N 3m 3m 3m 2/E DO I H JE