5.5-8 A freight-car axle AB is loaded approximately as shown in the figure, with the forces P representing the carloads (transmitted to the axle through the axle boxes) and the forces R representing the rail loads (transmitted to the axle through the wheels). The diameter of the axle is d = 82 mm, the distance between centers of the rails is L, and the distance between the forces P and R is b = 220 mm. Calculate the maximum bending stress max in the axle if P = 50 kN. b L b B

5.5-8 A freight-car axle AB is loaded approximately as shown in the figure, with the forces P representing the carloads (transmitted to the axle through the axle boxes) and the forces R representing the rail loads (transmitted to the axle through the wheels). The diameter of the axle is d = 82 mm, the distance between centers of the rails is L, and the distance between the forces P and R is b = 220 mm. Calculate the maximum bending stress max in the axle if P = 50 kN. b L b B

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

3-In the figure given below, P(load) and M(moment) effects from the mid point of the fixed beam from both sides. Find the displacement and reaction forces.(Please use your own words. M
The true option
The channel shape cross-section and the rectangular cross-section shown in the Figure Q4 are made of materials with elastic-perfectly plastic behaviour. The yield stress of the material used for the channel shape cross-section is oy = 473 MPa, whereas that used for the rectangular cross- section is 0.850y. Compute the thickness of the web, t, of the channel shape section if the two cross sections have identical plastic bending moment about the z-axis. In Figure 4, h= 77 mm, b=46 mm, a=11 mm, H=77 mm, d= 46 mm N b h a + N a | d H
In the following figure, there are two equal couples with a magnitude of M = 15 kNm. They act in opposite directions while being applied to the channel beam AB. These couples cause the beam to bend in the horizontal plane. Find: 1) Stress at point C 2) Stress at point D 3) Stress at point E
A simply supported beam is subjected to the load distribution shown in figure, which is symmetrical about the middle of the beam. What would be the reactions at the supports? (Use SI system if your roll number is less than or equal to 100 and use US customary system if your roll number is greater than 100). (Roll No 196) Also replace this force by an equivalent force couple system at the right edge of the beam if your roll number is odd and replace this force by an equivalent force couple system at the left edge of the beam if your roll number is even. The load type is Elliptical, w, = 415 L= Any value of your choice 2L Figure for Question No.1
4.5-13 A beam ABC with a protrusion at one end is subjected to an equally distributed load = 12 kN/m and a moment of magnitude 3 kN m at point C (see figure). Draw a shear force diagram and a bending moment diagram for this beam.
A railroad tie (or sleeper) is subjected to two rail loads, each of magnitude P = 177 kN, acting as shown in the figure. L 9 £a The reaction q of the ballast is assumed to be uniformly distributed over the length of the tie, which has cross-sectional dimensions b 300 mm and h = 250 mm. Calculate the maximum bending stress o (in MPa) in the tie due to the loads P, assuming the distance L = 1,500 mm and the overhang length a = 495 mm. (Enter the magnitude.) max MPa
A beam, supported by hinge and roller, is subjected to the forces shown in the figure, and a clockwise moment at point D. Calculate and indicate the directions of the reactions at the supports.
4. A universal beam ABC is simply supported at A and B. The beam is under multiple loads as shown in the Figure. Section AB is UDL with a magnitude of 40 kN/m. At point C, there is a 20 kN load and a moment of 100 kN.m. Calculate and draw the shear and moment diagram for the beam. 20 kN 40 kN/m 8 m B. 3 m 100 100 kN m
es A gear reduction unit uses the countershaft shown in the figure. Gear A receives power from another gear with the transmitted force FA applied at the 20° pressure angle as shown. The power is transmitted through the shaft and delivered through gear B through a transmitted force Fg at the pressure angle shown. For the steel countershaft specified in the table, find the deflection and slope of the shaft at point A. Use superposition with the deflection equations in Table A-9. Assume the bearings constitute simple supports. In the figure below, FA is 310 lbf and the diameter of the shaft (dshaft) is 1.29 in. dshaft Gear A 20-in dia. 16 in FA 20⁰ The deflection at point A is The slope at point A is 14 in 100 Gear B 8-in dia. rad. 9 in in. B FB 20°
ANSWER ALL FOR UPVOTE. INCOMPLETE WORK NO UPVOTE. THANK YOU