5.5-4 A simply supported wood beam AB with a span length L = 4 m carries a uniform load of inten- sity q = 5.8 kN/m (see figure). (a) Calculate the maximum bending stress o max due to the load q if the beam has a rectangular cross section with width b = 140 mm and height h = 240 mm. %3D (b) Repeat part (a) but use the trapezoidal distrib- uted load shown in the figure part b.

5.5-4 A simply supported wood beam AB with a span length L = 4 m carries a uniform load of inten- sity q = 5.8 kN/m (see figure). (a) Calculate the maximum bending stress o max due to the load q if the beam has a rectangular cross section with width b = 140 mm and height h = 240 mm. %3D (b) Repeat part (a) but use the trapezoidal distrib- uted load shown in the figure part b.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A simply supported beam is loaded with apoint load, as shown in the figure. The beam is a steelwide flange shape (W 12 X 35) in strong axis bending. Calculate the maximum deflection of the beam andthe rotation at joint A if L =10 ft, a = 7 ft, b = 3 ft,and P = 10 kips. Neglect the weight of the beam.
A wide-flange beam (see figure) is subjected to a shear force V. Using the following dimensions of the cross section, calculate the moment of inertia and then determine the following quantities. b = 6 in., t = 0.5 in., h = 11 in., h, = 9.3 in., V = 25 kips Note: Disregard the fillets at the junctions of the web and flanges and determine all quantities, including the moment of inertia, by considering the cross section to consist of three rectangles. (a) the maximum shear stress T, (in psi) in the web max psi (b) the minimum shear stress T (in psi) in the web min psi (c) the average shear stress 7aver (obtained by dividing the shear force by the area of the web) and the ratio max aver (Enter your answer for Taver in psi.) 'aver psi max Taver V web (in kips) carried in the web and the ratio V (d) the shear force V. web V. kips web V web V
A fixed-end beam is subjected to a pointload at mid-span. The beam has a rectangular crosssection (assume that the h/b ratio is 2) and is made ofwood (E =11GPa).(a) Find height h of the cross section if the maximumdisplacement of the beam is 2 mm.(b) Calculate the displacement of the beam at theinflection points.
5.5-13 Determine the maximum tensile stress o, (due to pure bending about a horizontal axis through C by positive bending moments M) for beams having cross sections as follows (see figure). (a) A semicircle of diameter d (b) An isosceles trapezoid with bases bị = b and bɔ = 4b/3, and altitude h (c) A circular sector with a = 1/3 and r = d/2 C C a a (a) (b) PROB. 5.5-13
The Cantilever beam in Fig. 5, has a circular cross section (diameter-100 mm) (a)find the shear stress in the beam in points (a,b.c.d and e) due to applied the uniform load 3 kN/m and the torque 4kN.m. (2) Sketch the shear stress distribution over the cross section. Dia 100 mm B. 3 kN/m 4 kN.m C. 4 m 1 m Fig
1. A simply supported wood beam AB with span length L = 8 m carries a uniform load of intensity q10.8 kN/m and a concentrated load P=25 kN at a distance a = 2.5 m from RH end (see figure). a. Calculate the maximum bending stress due to the load if the beam has a rectangular cross section with width b = 150 mm and height h=320 mm. You will need to set up Shear and Moment functions to determine MMax- b. Calculate the shear stresses in the beam (at the location of maximum shear force) at points located at the Neutral Axis and 40 mm, 80 mm, 120 mm and 160 mm from the N/A of the beam. From these calculations, plot a graph showing the distribution of shear stresses from top to bottom of the beam. 4 L a T tod h
5.5-13 Determine the maximum tensile stress o, (due to pure bending about a horizontal axis through C by positive bending moments M) for beams having cross sections as follows (see figure). (a) A semicircle of diameter d (b) An isosceles trapezoid with bases b¡ = b and b2 = 4b/3, and altitude h (c) A circular sector with a = m/3 and r = d/2 %3D |y C Xc a (a) (b) (c)
The beam AB, shown in Figure 1a, with length L = 4.5 m is subjected to a uniform distributed load w = 13 kN/m and a concentrated moment M = 18 kN.m applied at point B. The beam has a rectangular cross-section with height h = 183 mm, width b = 98 mm, and constant thickness t = 12.5 mm as shown in Figure 1b. Take E = 200 GPa. 1 Determine the slope at point B 2 Determine the vertical displacement at point B [
A beam had an isosceles triangular cross section (see figure below). The maximum flexural stress is limited to 90 MPa. Determine the magnitude of the allowable bending moment M.
Two vertical forces of P = 240 lb are applied to a simply supported beam shown below having the given cross section shown below. Using a = 30 in., L = 84 in., b = 3.0 in., d = 4.0 in., and t = 0.5 in., calculate the bending stresses produced in the top and bottom of the beam.
A beam has a bending moment of 3.5 kN-m applied to a section with a hollow circular cross-section of external diameter 3.6 cm and internal diameter 2.4 cm . The modulus of elasticity for the material is 210 x 109 N/m2. Calculate the radius of curvature and maximum bending stress. Also, calculate the stress at the point at 0.5 cm from the neutral axis (i) The moment of inertia = ii) The radius of curvature is (iii) The maximum bending stress is iv) The bending stress at the point 0.5 cm from the neutral axis is
A tapered cantilever beam AB of length L hassquare cross sections and supports a concentratedload P at the free end (see figure part a). The widthand height of the beam vary linearly from hA at thefree end to hB at the fixed end.Determine the distance x from the free end A to thecross section of maximum bending stress if hB = 3hA.(a) What is the magnitude σmax of the maximumbending stress? What is the ratio of the maximumstress to the largest stress B at the support?(b) Repeat part (a) if load P is now applied as a uniformload of intensity q = P/L over the entirebeam, A is restrained by a roller support, andB is a sliding support (see gure part b).