5.49 Air in a piston/cylinder goes through a Carnot cycle with the P-v diagram shown in Fig. 5.21. The high and low temperatures are 600 K and 300 K, respectively. The heat added at the high temperature is 250 kJ/kg, and the lowest pressure in the cycle is 75 kPa. Find the specific volume and pressure after heat rejection and the net work per unit mass.

Q: Air is contained inside a simple piston cylinder device as shown in the figure. It expands from…

A:

Q: Q3:In a gas turbine unit, the gases flow through the turbine and the power developed by the turbine…

A:

Q: Air at a temperature of 500 0C is compressed at a constant pressure of 1.2MPa from a volume of 2 m3…

A: Q= U + W W at constant P = P*delta V Q = change in enthalpy at constant pressure change in enthalpy…

Q: IS sidered as a quasi-equilibrium process such tha ate.

A: To determine the Required Flowrate

Q: Two heat engines receive heat from a source at temperature of 550◦C. Heat engine "A" receives 200 kJ…

A:

Q: Qi: One kg of steam undergoes a reversible isothermal process from 20 bar and 250°C, to a pressure…

A:

Q: There is a rigid tank initially with water in a critical state, which after a heat transfer process…

A:

Q: Provide the given, manula step by step solution, and diagram for below problem.  The efficiency of…

A:

Q: A certain gas with cp = 0.529 Btu/lb.R and R=96.2 ft.lb/lb.R, expands from 5 cu ft and 80°F to 15 cu…

A:

Q: are bied 4 16/min of oxygen at constant volume from 200 psia and 2400°R. 800°R. For non-flow find…

A:

Q: EXERCISES ON PROPERTIES OF STEAM 3). Ten kg of water 45 °C is heated at a constant pressure of 10…

A:

Q: A cycle works with one kg of air and is compressed through a polytropic process (pv12 = C) %3D from…

A:

Q: A cycle starts with an adiabatic compression of the air from state a with a volume V3 to state b…

A: For solution refer below images.

Q: Air undergoes an isentropic compression (PV^1.4 = c) process from initial pressure ar volume of 100…

A:

Q: A cycle works with one kg of air and is compressed through a polytropic process (pv12 = C) from…

A:

Q: At the start of the compression process in the reciprocating compressor of refrigeration plant the…

A: Given data :-  Start of compression = 1.5 bar  PV1.2 = constant P2 = 6.5 bar    Find :-  @ change of…

Q: H.W. 4.6 A steam power plant has steam entering at 70 bar, 450°C into HP turbine. Steam is extracted…

A:

Q: 3.23 A small, high-speed turbine operating on compressed air produces a power output of 100 W. The…

A: P1= 400 kPa T1= 50∘C P2= 150 kPa T2= -30∘C W˙output= 100 W= 0.1kW   Assumptions: i) Velocities are…

Q: 16. A perfect gas has a valuen of R = 58.8 ft-lb/lb-R and k = 1.26. IF 20 %3D BTU are added to 5 lb…

A: Given:  R = 58.8 ft-lb/lb-R   (1ft-lb/lb-R = 0.0054kJ/kgK) R = 58.8 × 0.0054 = 0.31752 kJ/kgK Heat…

Q: A 5 m3 rigid tank has propane at 500 kPa, 700 K and connected by a valve to another tank of 0.7 m3…

A:

Q: 4.54 kg mass of water vapor at 100kPa (abs) and an entropy of 8.0333 kJ/kg K; undergo a process at…

A: Use fluid property calculator or steam table to solve this problem

Q: Steam enters a throttling valve as a two-phase mixture at a pressure of 20 bar and a speed of 15…

A: The given data in the problem is shown in the following attached image:

Q: Given 0.603MW electrical power supplied to a boiler when the temperature of the entering water is 20…

A: The inlet and exit temperature respectively are 20 degree Celsius and 89 degree Celsius. Also, the…

Q: Q17 An ideal gas (Cp = R and C₂ = R), undergoes the following mechanically reversible changes in…

A: The ratio of the specific heat capacity is,Draw the PV diagram for the given process.Note-The…

Q: A refrigerator using R-134a as the refrigerant is used to keep a space at -10°C by rejecting heat to…

A:

Q: In a closed container with a constant volume, there is air at a temperature of 300 K and a pressure…

A:

Q: Q2: A steam engine receives steam at 4 bar, dryness fraction 0.8, and expands it according to law…

A:

Q: A single stage reciprocating air compressor is required to compress air at the rate of 1 kg/s from…

A: m=1kg/s P1=0.95 bar T1=298KP2=10 bar n=1.35

Q: .A heat pump design creates a heating effect of 35 kW while using 15 kW of electrical power. he…

A:

Q: 2.A piston cylinder arrangement contains steam at 10MPaa saturated liquid. Heat was transferred…

A: PHigher =10 Mpa or 100 bar Plower=2 Mpa or 20 bar Now with the help of steam table we need to…

Q: 1 Helium is compressed through a compressor steadily. At the inlet the pressure is P₁= 100kPa and…

A:

Q: 40°C 4. A mixing chamber receives 5 kg/min of ammonia as saturated liquid at -20°C from one line (1)…

A:

Q: 1. A closed tank, V = 10 L, containing 5 kg of water initially at 25 ° C, is heated to 150 ° C by a…

A: The step by step solution is given below.

Q: want to use the Otto cycle as (A) igerator and (B) a heat pump. Dra les, specify for each branch…

A:

Q: 1. Steam is supplied to a fully loaded 100 hp turbine at 200 psia with u, = 1160 BTU/b, v, = 2.6…

A: Given data Power developed in the turbine  = P = 100 hp  = 74.57 kWInlet Pressure =P1 =  200 psia =…

Q: 200Kg/min superheated steam at 40 bar and 350C enters a turbine through a 7.5cm ID pipe. It exits at…

A:

Work and Heat Transfer

It is generally related to thermal engineering which tells about the use, creation, conversion and transfer of heat energy between the systems. It is also considered that to transfer heat from one source to another, transfer of masses is also required. There are various mechanisms by which, transfer of heat takes place i.e. thermal conduction, convection, radiation or by change of phase. All these mechanisms have their own specific features which sometimes occur simultaneously within the same system.