5.2-10 For a PCM signal, determine the minimum necessary L if the compression parameter is μ = 100 and the minimum SNR required is 42 dB. Recall that L = 2" is required for a binary PCM. Determine the output SNR for this value of L. 5.2-11 Five sensor output signals, each of bandwidth 240 Hz, are to be transmitted simultaneously by binary PCM. The signals must be sampled at least 20% above the Nyquist rate. Framing and synchronizing requires an additional 0.5% extra bits. The PCM encoder of Prob. 5.2-10 is used to convert these signals before they are time-multiplexed into a single data stream. Determine the minimum possible data rate (bits per second) that must be transmitted, and the minimum bandwidth required to transmit the multiplex signal.

5.2-10 For a PCM signal, determine the minimum necessary L if the compression parameter is μ = 100 and the minimum SNR required is 42 dB. Recall that L = 2" is required for a binary PCM. Determine the output SNR for this value of L. 5.2-11 Five sensor output signals, each of bandwidth 240 Hz, are to be transmitted simultaneously by binary PCM. The signals must be sampled at least 20% above the Nyquist rate. Framing and synchronizing requires an additional 0.5% extra bits. The PCM encoder of Prob. 5.2-10 is used to convert these signals before they are time-multiplexed into a single data stream. Determine the minimum possible data rate (bits per second) that must be transmitted, and the minimum bandwidth required to transmit the multiplex signal.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Write the differential equation for t > 0 for thecircuit of Figure P5.27.
RI R5 Ginen: R,= l0.2. R4 = 102 R5 P - 6oa. Find RT.
Write the differential equation for t > 0 for thecircuit of Figure P5.32.
Please answer in typing format solution Please answer in typing format solution Thanks in advance thanks
3) The transfer function of a control system is given by G(s) = 25/ (s² + 6s + 25). The first maximum value of the response occurs at t, which is given by: a) π/2 b) π/8 c ) π/4 d) n 4) If the unity feedback system is given by the open loop transfer function G(s) = ks? / [(1 + 0.3s) (1+ 0.05s)], what would be the initial slope of magnitude plot? a) a. 20 dB/decade b) b. 40 dB/decade с) с. 60 dB/deсade d) d. Unpredictable
Determine the initial and final conditions for thecircuit of Figure P5.29.
Write the differential equation for t > 0 for thecircuit of Figure P5.52.
Q5) In the circuit shown in Figure, find: 1) R 2) last. I E-24V
Write the differential equation for t > 0 for thecircuit of Figure P5.41
Find the transfer function and the dynamical-equation description of the network in Figure P3-23. Do you think the transfer function is a good description of this system? Also answer why you think the transfer function is/is not a good description; how would your answer change if the active resistor of resistance -1 ohm is replaced by a passive resistor of resistance +1 ohm? 1 F -1 S2 Current source I F Figure P3-23
L-1 loge s2+1 s2+9 = .......
5.47 Use Thévenin's theorem to find 1, in the network in Fig. P5.47. 2 k2 24 V 6 k 2 mA 2 mA 3 k. 3 4 kn Figure P5.47