5.15 (WILEYa Water at 0.1 m/s and alcohol (SG = 0.8) at 0.3 m²/s aremixed in a y-duct as shown in Fig. 5.15. What is the average densityof the mixture of alcohol and water?Water andalcohol mixWaterQ = 0.1 m³/sAlcohol (SG = 0.8)Q = 0.3 m3/sFigure P5.15

Given Data Flow rate of water is :QW=0.1 m3/s Flow rate of alcohol is: QAL=0.3 m3/s Specific…

5.15 (WILEYa Water at 0.1 m/s and alcohol (SG = 0.8) at 0.3 m³/s mixed in a y-duct as shown in Fig. 5.15. What is the average der of the mixture of alcohol and water? Water and alcohol mix Water Q = 0.1 m/s

5.15 (WILEYa Water at 0.1 m/s and alcohol (SG = 0.8) at 0.3 m³/s mixed in a y-duct as shown in Fig. 5.15. What is the average der of the mixture of alcohol and water? Water and alcohol mix Water Q = 0.1 m/s

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Here, 20 degree celcius water is being siphoned from a reservoir, see attached image. What would be the minimum flow rate be, without cavitation occuring in the system at points 2 and 3?
A fluid with a density of 0.8 g/cm3 is being emptied from a very large tank through a small cylindrical opening with a diameter d. Use the figure below to calculate a) the diameter d_of the opening if the mass flow rate at point 2 is 1.45 kg/s, and b) the flow velocity at point 3. 1. H = 4 m d = ? 3 h = 1 m 2.
Water flows at 0.72 m/s through a pipe 17 cm in diameter when the pressure is 460,000 Pa. What is the water velocity & the pressure in the pipe if it shrinks down to 6 cm in diameter. Note: (The pipe is horizontal & ρwater = 1000 kg/m3.)
Water flows out of 5 mm x 200 mm slots in a sprinkler as shown. The mass flow rate is 15 kg/s. 200 mm 250 mm a. Find the torque required to prevent the sprinkler from rotating. b. Find the rotation rate of the frictionless sprinkler when released.
As seen in the figure above, the water is directed downward in the installation with a 25 ° narrowing elbow in a piping system with a volumetric flow of 0.025 m3 / s. Effective pressure at 1 point is measured as 2 bar. Calculate (a) the effective pressure at point 2 (b) the x and y components of the force required to hold the elbow in place and the resultant force in the case where the flow is frictionless and gravitational effects are neglected. (pwater=1000 kg/m3, g=9.81m/s2)
Q6) Calculate the hydraulic horsepower for pumping 500 gal / min from an inlet pressure of 5 psig to an outlet pressure of 30 psig (a) For water. (density 1000kg/m³) (b) For gasoline. (density 700 kg/m³) Discuss the difference for the pump power of (a) and (b) Q7) How many horsepowers are required to compress 20 lbmol/h of helium (k = 1.666) from 1 atm at 68°F to 10 atm using; (a) (b) (c) 68°F? An isothermal compressor? An adiabatic compressor? A two-stage, adiabatic compressor with optimum interstage pressure and intercooling to
3.
A horizontal jet of water 2x103 mm2 cross-section and flowing at a velocity of 15 m/s hits a flat plate at 60o to the axis (of the jet) and to the horizontal. The jet is such that there is no side spread. If the plate is stationary, calculate a) the force exerted on the plate in the direction of the jet and b) the ratio between the quantity of the fluid that is deflected upwards and that downwards. Assume that there is no friction and no shear force.
Gentlemen, please check and help me with question #3 Tank filled with water and orifice diameter of 3 cm in the bottom. Height between centre of orifice and water level 3 m. Coefficient of discharge - 0.64, coefficient of velocity- 0.97. Find: 1. Actual jet velocity? This one I know how to do. V(actual) = square root from 2gH 2. Jet diameter? This one I know as well. Coefficient of contraction= coefficient of discharge/ coefficient of velocity Diam of jet we will find from formula: Coefficient of contraction = (diameter of jet/diameter of orifice)^2 3. How long will it take for jet to be established?
Problem 4 (10 D A hydrant nozzle shown in Fig. 4 has a diameter of 100 mm at the inlet (flange). At the outlet of the hydrant, the diameter reduces to 30 mm. The fluid velocity and gage pressure at the inlet are 2 m/s and 323 KPa, respectively. The density of water is 1000 kg/m³. Neglect the weight of the pipe. Assume the flow is steady and determine: a) The jet velocity at the outlet b) The horizontal force acting on the flange PORT c) The moment acting on the flange (Point T 8 m V₂