5.10 kg of R-134a at 300KPA fills a rigid container whose volume is 14 L. Determine the temperature and total enthalpy in the container. The container is now heated until the pressure is 600 kPa. Determine the temperature and total enthalpy when the heating is completed. R134a 300kPa 10kg 14L

Q: Question: Calibration data for the chromatographic determination of Amoxicillin in a mixture of…

A: The concentration and peak area data of a drug is given.

Q: Discuss the Fundamentals of Unit Processing.

A:

Q: Question: Discuss the sedimentation experiment in the form of a question and answer?

A: Sedimentation is the process of separation of suspended solids from a solution by gravity settling…

Q: Please all options information and correct answer

A: B. A line tangent to the velocity of the fluid An imaginary line in a fluid flow field that has its…

Q: When the temperature sensor indicates a rise in the infant incubator, what do you expect the problem…

A: Infant incubator is a device which is used to provide sufficient warmth at a desired temperature and…

Q: Q2/ Based on your knowledge in atomic bonding and structure, give some typical examples showing that…

A: Atomic bonding Atomic bonding is the process in which molecules and atoms do interact. They are also…

Q: Make a brief discussion on waste planning and waste managment in terms of waste hierarchy.

A: Waste planning is the pre incident planning to prepare the group to manage the waste effectively. In…

Q: Write a brief summary explaining what is meant by the standards ISO 9001 and ISO 14001…

A: To Do Write about standards ISO 9001 and ISO 14001 certification and show pictures of two products…

Q: LPG is one form of application of physical changes a. Explain what happened to the LPG. b. Add…

A: a) Physical change is a kind of exchange where the physical properties of matter change. A exchange…

Q: By heat exchange, the butane fed into the reactor is brought to the reaction tempera- ture of 1000K…

A: The heat amount added to a chemical reaction or removed from a chemical reaction is called the heat…

Q: Why is engaging in MVPAs important in one’s health?

A: The importance of MVPA for health is to be mentioned.

Q: The use of total reflux corresponds to ___________.   a minimum number of stages   b optimum…

A: When reflux ratio will increase the wide variety of stages of plate decreases. The Total reflux…

Q: View factor F12 0.50 0.40 0.30 0.20 0.10 0 Y=0.1 1.0 0.2 0.3 0.4 0.6 0.8 1.0 1.5 3.0 8.0 USE THIS…

A: Solution:Step 1:

Q: II. The adiabatic exothermic irreversible gas-phase reaction 2A +B→ 20 is to be carried out in a…

A:

Q: I couldnt undertsnad the hand writing and the unit conversion used

A:

Q: Mof oxygen and 0.4M of reaches new equilibrium at 25°C. Question 3: The vapor pressure of a solution…

A:

Q: help  please answer in text form with proper workings and explanation for each and every part and…

A: Step 1: (1)2-chloropropane is symmetric molecule has plane (vertical) of symmetry. A plane of…

Q: Describe the implementations of multiple activity charts during method analysis.

A: Introduction Multiple activity charts are the process charts based on time scale. These are tools of…

Q: An aqeous solution of a non volatile solute boils at 100.17oC. At what temperature will the solution…

A: For the depression in boiling point, it is known that; ∆Tb = Molarity×kb Thus, 0.17 = Molarity×0.512…

Q: What is varied to achieve optimal control?

A: The quantity which varies due to which optimal control can be achieved is to be mentioned.

Q: Direction: From the presented lesson on the guidelines and format in research, can you identify…

A: Introduction In research methodology, a guideline is an advice or rules on how to do something. An…

Q: From such an experiment, it was found that the concentration of hydrogen peroxide remaining after 65…

A: Given data: Initial concentraction of hydrogen peroxide; Co=57.90 moles/mLFinal concentration of…

Q: Q4) Recommend some possible methods to identify different materials without resorting to chemical…

A: some of the methods to identify different materials without sorting to chemical analysis or lengthy…

Q: How does the inside-out method reduce the time in BP, SR, and NR methods?

A: In Bubble Point (BP), Sum Rate (SR), and Newton Raphson (NR) methods, calculation of the k-values…

Q: • Calculate oil flow rate assuming constant J. Construct the IPR by using Vogel's method and the…

A:

Q: _____is the desired value of the controlled variable.

A: Given that there is given blanks we have to fill that blank by suitable word which satisfy that…

Q: Q4. (A) What is gas turbine why it is used for in plant rotating equipment. Briefly explain its…

A: (a). Gas Turbine A gas turbine is the soul of the power plants. Its main purpose is to generate…

Q: 160 E160 1610 D140 161 1620 1650 P160 RD160 父 V165 1630 1640 父 V166 1660

A: Feedback controls are widely used in modern automated systems. A feedback control system consists of…

Q: Give four challenges and suggest solutions for those challenges in Check Valve?

A: The challenges with the Check valve are to be mentioned along with the solutions of those…

Q: What are some emerging technologies in chemical engineering, and how are they impacting the field?

A: To state and describe some emerging technologies in Chemical engineering, and mention their impact…

Q: If you are planning to study chemical engineering, investigate what is meant by each of the…

A: Chemical engineering play a vital role in the engineering field. The main work of Chemical engineers…

Q: Q3. What are Gear pumps? Why they are noise in operations? Why they are categorized in the positive…

A: Hi, thank you for the question. You have posted multiple question. According to our according to our…

Q: 1. Why do we avoid cold and hot forming during cutting? . 2. Why is the sample rotated at an angle…

A: Only the 1st question is answered here because the exact one is not specified.    Metal forming is a…

Q: Write the mechanism of chain scission with examples.

A: Chain scission is a term used in polymer chemistry describing the degradation of a polymer main…

Q: What are (list and explain) some of the relationships between atomic scale and macro scale…

A: Understanding these relationships between atomic scale features and macro scale properties is…

Q: what is the meaning behind chemical engineerng?

A:

Q: How does screening work in the chemical industry? Explain each step of the screening process in the…

A:

Q: Differentiate between PFD and Process & Instrumentation Diagram (P&ID), in terms of their contents.

A:

Q: How to Calculate the value of activity coefficients by using excel sheet:

A: the formula gor excess gibb's free energy is called as margules 2 suffix model.  GERT= x1x2(Ax1+Bx2)…

Q: EXPERIMENT: ANALYSIS OF COAGULATION AND FLOCCULATION USING JAR TEST Please make the general…

A: Coagulation is the process of conversion of liquid into solid or semi-solid. The agents used for…

Q: What is meant by a group method?

A: The definition of the group method is to be mentioned.

Q: Briefly explain what is meant by “Control for Operability”.

A: The Art of Control for Operability: Keeping Your Process Running SmoothlyIn the heart of industrial…