5. What do a roof pendant, a septum, and a raft have in common? In what way(s) do they differ?
Q: What are the disadvantage of steel sheeting?
A: The disadvantage of steel sheeting are as follows:
Q: What is the type of this truss
A: Solution: There are different types of trusses used in the construction field like Howe Trusses…
Q: Explain light-transmitting concrete.
A: Light-transmitting concrete Light-emitting concrete has the ability to trap solar energy during the…
Q: What is the advantage of Interlocking steel sheeting?
A: Interlocking steel sheeting is defined as the long structural section made of steel and having a…
Q: What Lightweight Concrete?
A: Objective: To state what is Lightweight concrete. Solution: Lightweight concrete, as the name…
Q: What do beams develop?
A: Beams are the structural members which are loaded transversely. This transverse load can cause…
Q: Determine the degree of indeterminacy of the following truss
A: Given data : Member (m)=14 Joint (J)=8 Support reaction (R)=2+1=3
Q: Why is it so difficult to make cladding watertight?
A: Cladding Cladding is difficult to make watertight cause wind pushes water in any direction on the…
Q: Why are the beams called rolled shapes?
A: - Rolled shapes beams sections are thermo mechanically treated section with enhanced properties in…
Q: Design a flat plate supported on columns spaced at 5.5 m in both directions. The size of the column…
A: Given data, Flate plate dimension L1×L2 = 5.5×5.5 m Column dimension = 500×500 mm = 0.5×0.5 m…
Q: The slab of a residential building of size 4.3 m × 6 m is simply supported on all the ir sides on…
A: Solution:Thickness: lx>3.5take ld=25 i.e d=l25d=430025=172mm~175mmD=200mmEffective…
Q: What forces may cause water to penetrate the joints in cladding?
A: The forces which cause the water to penetrate into the joints of cladding:
Q: Describe the Effect of Tension Cracks.
A: Tension cracks are defined as the cracks which appear on the soil surface where the stability…
Q: HOW DID Lightweight Concrete made?
A:
Q: Define induced stresses ?
A: The internal resistance of a body to changes and deformation due to applied load is known as stress.…
Q: A rectangular beam having b=250mm and d=480mm is reinforced with five 25-mm diameter tension bars.…
A: b = 250 mmd = 480 mmAs = fc' = 21 MPafy = 345 MPa
Q: Q- RCC A T-beam roof section has the following particulars: Thickness of slab = 100 mm, Width of rib…
A: Given data- Thickness of slab Dr = 100 mm, Width of rib bw = 300 mm, Depth of rib = 500 mm, Centre…
Q: why are trusses mainly used on roofs?
A: A truss is a structural member that is used to carry the loads in different directions. A truss is a…
Q: Stone Cladding on Steel Trusses.
A: Solution: Stone cladding is basically defined as the the sheets of stone that are generally combined…
Q: why Concrete Cover is used to reinforcement?
A: Concrete Cover: Concrete cover is the concrete which is the cover provided for the reinforced…
Q: IX. Determine the global stiffness matrix [K] for the continuous beam shown in fig. i i 1 i 2 2)
A: For any beam having indeterminacy to find reaction and member forces stiffness matrix method is…
Q: Which braces do the roof system braces and braces between columns include? Subject : Concrete and…
A: The specific braces used in a roof system or between columns can vary depending on the structural…
Q: 1. Why is it that the spacing of floor joist or truss rafters need to be equal? How does it differ…
A: Spacing between consecutive floor joist or truss rafter need to be equal in order to distribute the…
Q: why is it that the spacing of floor joist or truss rafters need to be equal? how does it differ from…
A: Brief concept introduction- Joist spaces- A joist is a horizontal structural part that is used in…
Q: Part II. Beams 4. Draw the shear and moment diagrams for the loaded cantilever beam where the end…
A:
Q: What is secondary compression?
A: Secondary compression:- It is a continuation of the volume change that started during primary…
Q: In a plain concrete pedestal of M35 grade, the maximum bearing pressure at the base is found to be…
A: A plain concrete pedestal-M35 grade fck=35 N/mm2Maximum bearing pressure at the base, p=40…
Q: 9.1 A 100-ft-long loose-laid, roof membrane (a = 0.000 150 in/in-°F) will be installed on a flat…
A: solution Room member L =100 ft Given co efficient of thermal expansion α = 0.000150 in / in - °F…
Q: Can you expand these? especially the second part?
A:
Q: Why is iron added to concrete?
A: introduction- concrete- It is a paste that contains fine aggregates(sand), coarse aggregate(gravel),…
Q: please give me three examples of different types of tensile structures and their applications. and…
A: The tensile structure in Delhi:It refers to the building of roofs primarily using a membrane…
Q: A 2 hinged semi circular arch with radius - 4m is acted up on a load of 60 kN. The horizontal…
A:
Q: What is the definition of truss? When do we use trusses? What is the problem with the trusses?
A: The structural elements used to carry the load. Structural elements can be beam, columns, truss,…
Q: Draw any seven steel structure's shapes, also mention its aporopriate names.
A:
Trending now
This is a popular solution!
Step by step
Solved in 2 steps
