5. [vZ (cos + i sin) ( 6. 3-2i

Q: Write the formula for the time required to fill the cavity by the bottom gating system.

A: Given: Bottom gating system

Q: Which of the following statement is incorrect? Select one: O Friction is high for dry surface O…

A:

Q: If the analysis of the forces involved on an object produces a negative answer for a force: The…

A: If doing calculation and getting any force hwith negative that means, The negative sign indicates…

Q: What is section modulus?

A: The section modulus helps to calculate the outermost stress in the beam section. It is numerically…

Q: What are internal forces?

A: Internal forces are defined as the forces exerted by the particles of the body on each other within…

Q: The diameter of the cylinder in a scrap baling press is 150 mm. The stroke of the cylinder is 2.5…

A: This problem is related to fluid mechanics. Fluid mechanics is the subject of mechanical engineering…

Q: Warning-If not anything upto the mark, I'll report and dislike you. Draw figure of uniaxial state of…

A: Uniaxial State of stress-  this type of stress has only one principal stress. ie , when an object is…

Q: Each cylinder in a four-cylinder car engine has a bore diameter of 63.53 mm and the stroke for each…

A: Consider a vehicle engine where number of cylinder are situated whose bore diameter is D and stroke…

Q: Write the formula used to determine the average shear stress?

A: shear stress is the stress produced due to shear force.

Q: The coefficient of bend value in the energy loss due to bend in a pipe depends on the pipe diameter,…

A: Coefficient of bend value depends on ?

Q: Use Archimedes' principle on any case study in contextual engineering applications. Calculate its…

A: Given question: Use archimedes' principle on any case in contextual engineering applications.

Q: ood day. I am trying to review for examinations and require assistance for these questions... Horse…

A: Given

Q: 70 in Hg abs = psig

A: 70 in Hg abs

Q: Degree of drawing is measured in terms of; Reduction in strain Reduction in area O Reduction in…

A: Degree of drawing is measured in terms of: Answer: Reduction in area

Q: What would be the critical path and the project duration for M?

A: The network diagram has activities from A to M and different time intervals are given.

Q: 5.) A pin made of steel is inserted in a short hanging wooden member and is used to support load F =…

A: Given dataSupport load F = 20kNUltimate strength of the wood is 60Mpa in tension and 75MPa in…

Q: where do you get the form factor (y=.337) from? Please.

A: Form factor for full depth 20° at 24 teeth can be taken from standard table. I have provided the…

Q: I needed it to be solved using differential equation

A:

Q: Assume oz = 500, ay = 300, Txy = 250, oyicld = 350. Answer the following questions. Click here for…

A: GIVEN DATA σx= 500MPa σy= 300MPa τxy= 250MPa We have to find maximum and minimum normal stress on a…

Q: Q1) Define the following: 1) The stress & the strain 2) Mechanical stress and mechanical strain 3)…

A: Define the Following The stress and the strain Yield strength Tensile Strength Modulus of elasticity…

Q: FOLLOW THESE STEPS FOR UPVOTE Given Required Diagram Solution Conclusion Do not round off while…

A: At sea levelThe diameter of ballon d=8 indensity of air ρ=0.07498 lb/ft3Pressure P=14.7 psiawhen…

Q: Q4 Locate the cenroid -12 in. -12 in - 15 in. 15 in. 25 in. 9 in.

A: we know that the centroid of a right circular cone is at  a distance of  14th of its…

Q: Write the equation that relates applied stress to local maximum stress.

A: Stress concentration factors are generally used to relate applied stress to local maximum stresses.…

Q: Describe the hydrostatic stress?

A: When a force is imparted on a body, an internal resisting force is set up into the body, impeding…

Q: c) The bore of each cylinder in a six-cylinder car engine is 52 mm and the stroke for each piston is…

A:

Q: Write the flexure formula?

A: Flexure formula This formula is used to determine the internal bending stress when an external force…

Q: What does the shear flow measure?

A: The shear flow is defined as the shear force per unit length in a thin walled perimeter. The…

Q: Q4. The compound shaft shown in Figure Q4 is attached to rigid supports. For the bronze segment AB,…

A: As per Expert Q&A guidelines we are supposed to answer the first three parts of the given…

Q: Please help. Written on paper not typed on computer or keyboard please. Need help on all questions.…

A: Step 1:a. Equation for the differential area aligned horizontally The differential area element dA…

Q: DIFFERENTAITE SHEAR STRESS FROM SHEAR STRAIN. THEIR RATIO

A:

Q: 6. Three reservoir A, B and C are connected respectively with pipes 1,2 and 3 joining at a common…

A: Given:The elevation of the common junction D, The elevation of the reservoir A, The elevation of the…

Q: Write the nature of work done by an elongated spring?

A: The elongation produced in an ideal spring is directly proportional to the spring force F=−kx.

Q: 1- Metals is more - --than ceramic in this property. 2- The engineering design deals with ----and 3-…

A: Dear Student, As per the Bartleby answering guidelines we are supposed to answer first 3 questions.…

Entropy

In physics, entropy means the amount of disorder or the degree of randomness associated with a thermodynamic system. The system is not self-organized when the entropy of the system is high. For instance, when a system is at an elevated temperature, its molecules are in random motion, vibrating and colliding with each other. During this scenario, the probability of finding a molecule at a particular place twice, is low. Under this circumstance, the system can be said to be in a high entropy.