please help me in 5 1. Two wattmeters connected to measure the input to a balanced three-phase circuit indicate 2500 Wand 500 W respectively. Find the power factor of the circuit (a) when both readings are positive and (b) whenthe latter reading is obtained after reversing the connections to the current coil of one instrument.|(a) 0.655 (b) 0.3591] (City & Guilds, London)2. A 400-V, 3-phase induction motor load takes 900 kVA at a power factor of 0.707. Calculate the kVArating of the capacitor bank to raise the resultant power factor of the installation of 0.866 lagging.Find also the resultant power factor when the capacitors are in circuit and the motor load has fallen to300 kVA at 0.5 power factor.3. Two wattmeters measure the total power in three-phase circuits and are correctly connected. Onereads 4,800 W while other reads backwards. On reversing the latter, it reads 400 W. What is the total powerabsorbed by the circuit and the power factor?4. The power taken by a 3-phase, 400-V motor is measured by the two wattmeter method and thereadings of the two wattmeters are 460 and 780 watts respectively. Estimate the power factor of the motorand the line current.|296 kVA, 0.998 leading] (City & Guilds, London)[4400 W; 0.49| (Sheffield Univ. U.K.)[0.913, 1.96 AJ (City & Guilds, London)5. Two wattmeters, W, and W, connected to read the input to a three-phase induction motor runningunloaded, indicate 3 kW and 1 kW respectively. On increasing the load, the reading on W, increases whilethat on W, decreases and eventually reverses.Explain the above phenomenon and find the unloaded power and power factor of the motor.12 kW, 0.287 lag] (London Univ.)6. The power flowing in a 3-0, 3-wire, balanced-load system is measured by the two wattmetermethod. The reading on wattmeter A is 5,000 W and on wattmeter B is – 1,000 W(a) What is the power factor of the system?(b) If the voltage of the circuit is 440, what is the value of capacitance which must be introduced intoeach phase to cause the whole of the power measured to appear on wattmeter A?10.359; 5.43 (Meters and Meas. Insts. A.M.I.E.E. London)inn 1. -L-

5. Two wattmeters, W, and W, connected to read the input to a three-phase induction motor running unloaded, indicate 3 kW and 1 kW respectively. On increasing the load, the reading on W, increases while hat on W, decreases and eventually reverses. Explain the above phenomenon and find the unloaded power and power factor of the motor.

5. Two wattmeters, W, and W, connected to read the input to a three-phase induction motor running unloaded, indicate 3 kW and 1 kW respectively. On increasing the load, the reading on W, increases while hat on W, decreases and eventually reverses. Explain the above phenomenon and find the unloaded power and power factor of the motor.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

My sister goes to the cinema (three- * times) -Where does your sister go three times a month? How many time does your sister go to the cinema? How many times did your sister go to the cinema? -How many times does your sister go to the cinema? None of them is correct O
According to the given circuit diagram, the digital multimeter should measure one of the followings: O 122 ohms O 135 mA O 24 V O All of the above Chick Save and Submit to save and submit. Click Save All Answers to save all ansuuers.
Question No.76 The change in resistance of an electrical strain gauge with a gauge factor of 2.0 and resistance of 50 Q when subjected to a strain of 0.001 is:
Choices
2. A student measures resistance with a Digital Multimeter. Four 47O Q ±5% resistors are measured. One of the measured resistor values is not within the +5% tolerance. Which one of the following readings is within bounds? * 430.0 Q O 495.7 2 410.0 2 513.0 Q 450.6 Q
Which of the following values allows the MOST amount of current flow ina circuit? 10 Q O 1,000 Q 1,000,000 Q ore
I need answer within 5 minutes please please with my best wishes
170
5. R equivalent R, AO R OB
7
28a) The measuring range of a MC ammeter is found to be (0 – 75) mA. This low range ammeter is connected with a shunt resistance of 10 mΩ, in order to measure current values up to 90A. Determine the resistance of the ammeter.
The resistance of a 125 2 strain gauge changes by 1 ohm for 4000 micro strain. The gauge factor is O 2 3 O 31.25 O 31.25 x 10^{-3}