The linkage in the following figure has O2A = 0.8, AB = 1.93, AC = 1.33, and offset = 0.38 in. Thecrank angle in the position shown is 34.3° and angle BAC = 38.6°. Find a 3, A4, Ag and Ac for theposition shown for 02 = 15 rad/s, a2= 10 rad/sec² in direction shown.5.a) Using the acceleration difference graphical methodb) Using an analytical method.A3B0241

Here Given data of crank and slider mechanism Angular velocity of the link (2) W2 =15 rad/sec…

5. The linkage in the following figure has O2A = 0.8, AB = 1.93, AC = 1.33, and offset = 0.38 in. The crank angle in the position shown is 34.3° and angle BAC= 38.6º. Find a 3, A4, Ag and Ac for the position shown for 02 = 15 rad/s, a2= 10 rad/sec² in direction shown. a) Using the acceleration difference graphical method

5. The linkage in the following figure has O2A = 0.8, AB = 1.93, AC = 1.33, and offset = 0.38 in. The crank angle in the position shown is 34.3° and angle BAC= 38.6º. Find a 3, A4, Ag and Ac for the position shown for 02 = 15 rad/s, a2= 10 rad/sec² in direction shown. a) Using the acceleration difference graphical method

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q12: For the system Components of he force (F) on the ae x-axis and onto shown in figure c12); determine the the line oA 350 3007 Figure (12) F=SKN
a) An engine has a flywheel mass of 8-tonnes and a turning radius of 3 m. The energy fluctuation is 70 KN-m. The average speed of the engine is 160 rpm. Find the maximum speed value. b) A jet engine has a rotor with a weight of 500 N and this rotor rotates at 2400 rpm. Rotor It is suspended in the middle of the C and D bearings with a total distance of 600 mm between them and the center of gravity is rotated. 35 mm above its centre. By calculating the dynamic forces on the bearings, this system perform the balancing.
(c) In Figure Q4 (c), the 30 N block is moving up the smooth inclined surface at velocity and constant force of 2 m/s and 15 N, respectively. (i). Draw the kinetic diagram of all forces exerted on box (ii). Calculate the velocity of the block when it has moved 1 m up the surface from its present position.
A general fourbar linkage configuration and its notation are shown in Figure below. The link lengths, coupler point location, and the values of 02 and w2 for the same fourbar linkages as used for position analysis in Chapter 4 are redefined in Table below. For the row c, draw the linkage to scale and Using an analytical method calculate w3 and w4 and find the velocity of point P. find the velocities of the pin joints A and. RPA AY 2 04 02 04 FIGURE P6-1 Configuration and terminology for the pin-Jointed fourbar linkage of Problems 6-4 to 6-5 TABLE P6-1 Data for Problems 6-4 to 6-5† Row Link 1 Link 2 Link 3 Link 4 02 02 Rpa 83 6. 2 7 30 10 6. 30 b. 9 3 8 85 -12 9. 25 10 6. 8 45 -15 10 80 O73
A pinjointed fourbar linkage is shown in the figure below. The link lengths are L1 = 7.8 in., L2 = 2.9 in., L3 = 7.25 in. and L4= 3.5 in. Using the current position, 02-100°, the position analysis has determined that 04 = 214.25°. Currently, link 2 is traveling at 5.50 rad/s CCW Lep B. Figure 6.7 Four-bar linkage acceleration analysis The angular velocities of link 3 w3 and and link 4 Wa are: Select one: O a. w3 = 3.589 rad/s, Wa = -2.91 rad/s O b. w3 = 2.07rad/s, wa = -2.91 rad/s C. W3 = 2.7 rad/s, wa 3.428 rad/s O d. w3 = 2.07 rad/s, w4 = -3.38 rad/s
Use back-substitution to solve the system of linear equations. 2r+3y-3z=-4 - 8y – 7z=73 =-7 A (-8, -7, -3) B (-7, -8, -3) (5, -3, -7) (-3, -8, -7) E (-8,-3, -7)
Pls help me with my plates Block 4 slides in the slot in the fixed piece 1. Axis Q2 of crank 2 is fixed on 1. Q2A = 1.5 inches, and AB = 4.5 inches. Draw the mechanism, assuming dimensions for 1, if desired or use center lines only. Draw the four-bar linkage for this mechanism, properly rotate the linkage Q2ABQ4∞, name each link, and show the finite infinite cranks.
Problem 2 The linkage in Figure P7-5b has O,A = O2A = 0.75, AB= 1.5, and AC = 1.2 in. The effective crank angle in the position shown is 77° and angle BAC = 30°. Find a3, A4, AB,Ac for the position shown for @2 = 15 rad/sec and a2 = 10 rad/sec in the directions shown using an analytical method. (Hint: Create an effective linkage for the position shown and analyze it as a pin-jointed fourbar.)the linkage has a parallelogram form Assume rolling contact C @2 A 3 В a2 2 4 04
Figure below shows a four-bar linkage (non-scaled diagram) at an instant. The input angle is equal to the output angle (02 - 04) and the transmission angle is 30°. The input link is extended beyond joint B and an input force (Fin) is applied at the end of it, while an output force is drawn from the midpoint of the output link. If an output force of 30 N is desired from an input force of 10 N, how far the input link should be extended, i.e., what is the distance from point B to the point where Fin is applied. Fin B out undefined 02 04 A. Non-scaled diagram; AB = 10, CD=r4 = 30 (output), all in mm
write vector loop equation(s) theta2=57 also if a new length is constructed find its value. 02 57° 30° X L₁= 162 L2=40 L4=122 L3=96 0₁