5. The drinking water needs of an office are met by large water bottles. One end of a 0.25-in diameter plastic hose is inserted into the bottle placed on a high stand, while the other end with an on/ off valve is maintained 2 ft below the bottom of the bottle. If the water level in the bottle is 1.5 ft when it is full, determine how long it will take at the minimum to fill an 8-oz glass (= 0.00835 ft³) (a) when the bottle is first opened and (b) when the bottle is almost empty.

5. The drinking water needs of an office are met by large water bottles. One end of a 0.25-in diameter plastic hose is inserted into the bottle placed on a high stand, while the other end with an on/ off valve is maintained 2 ft below the bottom of the bottle. If the water level in the bottle is 1.5 ft when it is full, determine how long it will take at the minimum to fill an 8-oz glass (= 0.00835 ft³) (a) when the bottle is first opened and (b) when the bottle is almost empty.

Name: 5. The drinking water needs of an office are met bylarge water bottle
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: 5. The drinking water needs of an office are met bylarge water bottles. One end of a 0.25-in diameterplastic hose is inserted into the bottle placed on ahigh stand, while the other end with an on / off valveis maintained 2 ft below the bottom of the

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine the height of the mercury in the tube if the level of water in the tube is h = 0.3m and the depths of the oil and water in the tank are 0.6 and 0.5 m, respectively as shown in Figure Q5. Take po = 900 kg/m³, pw = 1000 kg/m³, and PHg= 13550 kg/m³. 0.6 m 0.5 m B h'=0.3 m
A low-pressure steam-having system designed for a building delivers heat to a heating coil at a temperature of 220°F. The coil is located 75 feet from the boiler is designed for a heating rate of 100,000 Btu/hr. Determine the pipe size that meets the design criteria and the total pressure drop.
The water level in a tank is 34 ft above the ground. A hose is connected to the bottom of the tank at the ground level and the nozzle at the end of the hose is pointed straight up. The tank cover is airtight, but the pressure over the water surface is unkown. Determine the minimum tank air pressure (gage) that will cause a water stream from the nozzle to rise 72 ft from the ground. A. 13.5 psi B. 14.4 psi C. 16.5 psi D. 15.5 psi With F.B.D.
The drinking water needs of an office are met by large water bottles. One end of a 0.35-in-diameter, 6-ft-long plastic hose is inserted into the bottle placed on a high stand, while the other end with an on/off valve is maintained 3 ft below the bottom of the bottle. If the water level in the bottle is 1 ft when it is full, determine how long it would take to fill an 8-oz glass (= 0.00835 ft3) (a) when the bottle is first opened and (b) when the bottle is almost empty. Take the total minor loss coefficient, including the on/off valve, to be 2.8 when it is fully open. Assume the water temperature to be the same as the room temperature of 70°F.
If a 200-gal. steel hydraulic reservoir twice as long as its square end section is wide and overheats the fluid with a temperature rise of 100°F, how large would the reservoir have to be to reduce the temperature rise to 70°F?
The pump is a device that is used to convert hydraulic energy into mechanical energy Select one: True False
On a trip to the beach (Patm 1 atm or 101.3 kPa), a car runs out of gasoline and it is necessary to siphon gasoline from a Good Samaritan's car. The siphon is a hose with a small diameter and to start the action it is necessary to insert one end into the tank full of gasoline, fill the hose with it through suction and then put the other end in a can that is placed under the tank level. The difference in pressure between point 1 (on the free surface of the gasoline in the tank) and point 2 (at the outlet of the tube) causes the liquid to flow from the highest elevation to the lowest. In this case, point 2 is located 0.75 m below point 1, and point 3 is 2 m above 1. The siphon diameter is 4 mm and friction losses in it must be ruled out. Determine: a) theminimum time to bring 4 L of gasoline from the tank to the can and b) the pressure at point 3. The density of the gasoline is 750 kg / m3.
Problem 1: The difference in mercury level of a pitot static tube connected to a submarine is 20 cm. Determine the speed of the submarine. The density of sea water is 1019 kg/m3. Assume Cv = 0.98.
Q1. A trapezoid-shaped tank used to supply potable water to a small area which includes 8 villas (Figure 1). The tank bottom base is 3 m, while the top base is 5 m. The tank is partially submerged vertically in water so that the top is 1 m above the surface and the bottom is 3 m below the surface. Determine the total force exerted on the trapezoidal wall by the water. Vertical Pipe line from overhear tank Main distribution line Overhead tank Secondary distribution line Villa Villa Valve Villa Villa G.L. Venturimeter Villa Villa Villa Villa Junction Figure 1. Water Supply and Distribution System Q2. The water flows through a horizontal Venturi-meter at section 2 in Figure 1. The inlet and throat diameters are shown in Fig. 2 below. A mercury filled a U-tube manometer connected to the inlet and throat shows a difference in mercury level of 300 mm. The specific gravity of mercury is 13.6. Determine the flow rate, and the difference in pressure between the inlet and throat. Throat Area, AT…