5. the absolute maximum bending moment in the simply supported beam due to the wheel loads of the HS20- 44 truck shown in Fig. 1-5 is: A-43 k-ft B- 134 k-ft C-314 k-ft Haft D-32 k-ft

Q: 4. D. B

A:

Q: tiate between focus and epicenter

A: solution of above problem is below:

Q: 3kLf 20 ft eliste Max = Max

A:

Q: Draw top, front and right view of the following isometric views

A: Top view

Q: A hexagonal prism of base edge 25 mm and height 50 mm is resting centrally on top of a rectangular…

A: The isometric drawing or isometric projection is projecting the object or structure in three…

Q: What is diffuser plate in an ESP?

A: In an electrostatic precipitator, when a polluted gas is passed through a high voltage field then in…

Q: Determine Ix and Tx.

A: GIVEN- A PLANE FIGURE TO FIND- MOMENT OF INERTIA ABOUT X-AXIS AND CENTROIDAL AXIS.

Q: Draw the shear force and bending moment diagrams and sketch the qualitative deflected shape.

A: The figure given in the question are as follows: w=1.5 klf

Q: DRAW THE SECTION INDICATED BY THE CUTTIN

A: Any view obtained by a projection on a plane other than the horizontal, frontal, and profile…

Q: USing Virtuall Work method Draw Bm.D and S. fD 2 2M

A: We have to draw shearing and bending moment diagram

Q: Arrange the following description in the form of profile level notes complete to elevation. A level…

A: The benchmark elevation is given as 12.135m.

Q: Draw the plan and elevation of the given line diagram. W W.C V KITCHEN D, 2100×1200 3600x2800 BATH V…

A:

Q: If a layer is set to plot but is currently frozen -1 .. or turned off, the layer is Plotted Not…

A: Plot command: Controls whether visible layers are plotted. If a layer is set to plot but is…

Q: from a point A 20m above the ground, the angle of elevation of the top of the tower is 29.33…

A:

Q: 3. What is the radius of 1/50 ac plot?

A: Assume area of plot is circular :we know area of circl is A=πR2

Q: 300N RL=

A: Given Simply supported beam Length, L = 3m Load, W = 300 N Distance of load from left support = 35cm…

Q: 5 TOP 10 8 FRONT ? Isometric View RSV

A:

Q: Find the areal scale for the following 3cm+09km

A: Given: Map distancex=3 cm Ground distanceX=9 km To find: Areal scale

Q: 6.29. The flowrate passing over this sharp-crested weir in a channel of 1 ft width is 3.5 cfs.…

A: Given  figure are:- As, we know that force exercted by the water on weir plate F =ρw·g·A·h' here ,…

Q: Find the coordinate of centroid of the shaded area ? y 6 cm 6 cm 3 ст 6 cm 3 cm

A: Consider the figure,

Q: What is Dutch (Deft) cone is consists of?

A: The cone penetration test (CPT) is a technique used to measure the geophysical characteristics of…

Q: 14000 mm 3000 mm 8000 mm 3000 mrm 12000 mm ww 0009

A: Given:- The radius of the semicircle = 3000 mm The thickness of the wall = 500 mm  To determine:- a)…

Q: the centroid of the shaded area by direct integration

A: Ixx=∫0b(h*xb)33dx Ixx=215h3[x]b0 Ixx=215h3b Similarly , Iyy=∫0by2(b-hy2h2dy Iyy=215b3h

Q: Locate the centroid y̅ of the area.

A: Consider the figure,

Q: Subtract 8.46 from 25.3.   25.3- 8.46

A: Subtract 8.46 from 25.3.

Q: g1= Station 18+26 18+00 17+00 16+00 15+68 g2= X 0 Elevation of BVC = gix 82-81x2 2L Elevation 899.02

A: Vertical Curve : Vertical curves, which may or may not be symmetrical, are supplied to alter the…

Q: , the rod reading is 1.159m, 120m from the beginning of the line rod reading is 1.434m, and finally…

A:

Q: External wall 2x4 sill plate runs along the perimeter 6m 1.5m 2m 2x4 studs spaced at 300mm o.c. 0 25…

A:

Q: rch Alt+Q) Heber John de Vera HI Review View Help ACROBAT O Record B Share so kN 40 kN/m lo kNm 20…

A:

Q: Determine the coordinates of the centroid of the shaded are 3″ 2"

A: To find centroid

Q: What is the slant distance of the centroid of the gate (y)? 2 m measured from A 3 m measured from C…

A: We have to determine the slant diatance of the centroid of the gate ( y^bar ) which can be from…

Q: igure P7-10. P7-10 Given the partial traverse shown in Figure P7-10 place the following items in the…

A:

Q: Determine the lk and I, for the plane & shaded region. Dimensions 7,5 in inches 3

A:

Q: DRAW OBLIQUE DEGREE 45°

A: Projections of an object are 2D views of that object when seen from any of the sides. There are…

Types and properties of steel

Steel is an alloy of iron. It is formed by heating iron and combining carbon (0.1-1.7%) with it and minor amounts of other elements such sulfur,  chromium, manganese, nickel, etc. Thousands of steel grades have been published, registered, or regulated around the world, each with its chemical composition, and special numbering systems have been devised in various countries to classify the vast number of alloys.