5. How do point loads and uniformdistributed load be represented in SFD?a) Horizontal lines and curved linesb) Curved lines and inclined linesc) Horizontal lines and inclined linesd) Cant represent any more6. What is the Sher Force at support B?2 KN/mBA1M→ 2Ma) 5 kNb) 3 kNc) 2 kNd) 0 kN7. Where do the maximum BM occurs forthe below diagram.10 KNBА2M→ 3Ma) -54 kNmb) -92 kNmc) -105 kNmd) – 65 kNm8. Which of the following are staticallydeterminate beams?a. Only simply supported beamsb. Cantilever, overhanging and simply supportedC. Fixed beamsd. Continuous beams9. A cantilever is a beam whosea. Both ends are supported either on rollers orhingesb. One end is fixed and other end is freeC. Both ends are fixedd. Whose both or one of the end has overhang10. For any part of the beam, between twoconcentrated load Shear force diagram is a

Answer:- 5 . c 6. d 7. no clear udl mentioned over span 8. b 9. b

5. How do point loads and uniform distributed load be represented in SFD? a) Horizontal lines and curved lines b) Curved lines and inclined lines c) Horizontal lines and inclined lines d) Cant represent any more 6. What is the Sher Force at support B? 2 KN/m B A 1M → 2M a) 5 kN b) 3 kN c) 2 kN d) 0 kN 7. Where do the maximum BM occurs for the below diagram. 10 KN B A 2M > 3M a) -54 kNm b) -92 kNm c) -105 kNm d) – 65 kNm Which of the following are statically 8. determinate beams? a. Only simply supported beams b. Cantilever, overhanging and simply supported C. Fixed beams d. Continuous beams 9. A cantilever is a beam whose a. Both ends are supported either on rollers or hinges b. One end is fixed and other end is free C. Both ends are fixed d. Whose both or one of the end has overhang

5. How do point loads and uniform distributed load be represented in SFD? a) Horizontal lines and curved lines b) Curved lines and inclined lines c) Horizontal lines and inclined lines d) Cant represent any more 6. What is the Sher Force at support B? 2 KN/m B A 1M → 2M a) 5 kN b) 3 kN c) 2 kN d) 0 kN 7. Where do the maximum BM occurs for the below diagram. 10 KN B A 2M > 3M a) -54 kNm b) -92 kNm c) -105 kNm d) – 65 kNm Which of the following are statically 8. determinate beams? a. Only simply supported beams b. Cantilever, overhanging and simply supported C. Fixed beams d. Continuous beams 9. A cantilever is a beam whose a. Both ends are supported either on rollers or hinges b. One end is fixed and other end is free C. Both ends are fixed d. Whose both or one of the end has overhang

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Question 4 (combined loading and stresses) The rectangular block of negligible weight in Figure for question 4, is subjected to a vertical force of 100 kN, which is applied to its corner. The block's cross section is 0.4m x 1.0m. Using principle of superposition, determine the value of normal stress (i.e. perpendicular to the cross section = parallel to the vertical force) at four corners, i.e. OA, OB, oc, and op. Note the stress directions (i.e. tension or compression). (in MPa). 100 KN 1.0m A 0.4 m B D
Note the values: E = 0 C = 8 40 KN 28 KN po
Please show an complete answer and FBD
strength of materials... answer only Draw the shear-force and bending-moment diagrams for the simply supported beam shown. Determine the shear force 3.5 m to the right of point A if W = 9.9 kN/m, T = 14.75 kNm, m = 11.1 m, and n = 5.9 m. Round off the final answer to four decimal places.
Hoi Problem II. A supporting rope is loaded with a line load q(x) = q0 between points A and B. The rope shall be stretched such that the slope of the rope at point A is zero. If (= 10 m and h = 2.3 m, determine the (a) horizontal tensile force and (b) the maximum force in the rope. q0= 36.137 kn B
A simply supported beam 4 m long has a cross section shown. Determine the maximum uniformly distributed load which can be applied over the entire length of the beam if the shearing stress is limited to 1.9 MPa. Answer must be in kN/m. Given: b = 130 mm and d = 160 mm. 280 mm b. 170mm
A cantilever beam carries a trapezoidaldistributed load (see figure). Let wB = 2.5 kN/m,wA = 5.0 kN/m, and L = 2.5 m. The beam has amodulus E = 45GPa and a rectangular cross sectionwith width b = 200 mm and depth h = 300 mm.Use the method of superposition and Cases 1 and8 in Table H-1 to calculate the def lection and rotationat B.
A simply supported beam AB = 10 m has a hollow rectangular cross-section with 14 cm as width, 23 cm as depth, and inner thickness as 1 cm is subjected to a point load of 7 N & 5 N acting at C and D respectively and a uniformly distributed load (UDL) of 7 N/m starts from mid-span and ends at the right support of the beam. Determine the maximum bending stress and the bending stress at 1 cm from the top. Take AC = 2 m & CD = 1 m. Solution: i) Reaction force at B = Answer and unit for part 1 ii) Reaction Force at A = Answer and unit for part 2 iii) The distance from B at which the shear Force value changes from "-" to "+" = Answer and unit for part 3 iv) Maximum Bending Moment (Please write the Maximum bending moment valve in "Nm") = Answer and unit for part 4 v) Moment of Inertia, I = Answer and unit for part 5 vi) Maximum bending stress = Answer and unit for part 6 vii) Bending stress at 1 cm from the top =
Please answer with complete free diagrams, etc..
Please help
A weight W= 120 kN is being supported by steel sectionswith force T, force F, and force C. The coordinates of A,B, C, and D are given. Assume that E is the origin (0,0,0).Determine Forces T, F, and C. PROVIDE FBD
Take that w0w0w_0 = 4.8 kN/mkN/m.