5. Determine the moment of the 360N about a) point A, and b) point B 360 N 40° 100 mm 225 mm A 25• ERSITY

Q: A gear reduction system consists of two gears: E and X. Gear E rotates clockwise with a constant…

A: Given data: αE=4.5 rad/s2ωE=7 rad/s Need to determine select the correct statement.

Q: A stone is dropped down a well and 5 sec later, the sounds of the splash is heard. If the velocity…

A:

Q: Volume ama the itCTIlal CHcrgy. 4. A vessel of a volume 0.03m3 contains dry saturated steam at 20…

A:

Q: Answer the following

A: Given data: The specific gravity of oil, (SG)oil = 0.85. Density of water, ρw = 1000 kg/m3. The…

Q: solutions are given, please resolve to get these solutions

A:

Q: 40° C

A: The diagram of force vectors is given as, The co-ordinate at point A,The co-ordinate at point B,The…

Q: 4. In raising the pole from the position shown, the tension T in the cable must supply a…

A:

Q: Answer the following

A: Draw the free-body diagram of the reach-stacker with the arm.

Q: 1. Why engineers are considered a significant segment of society?

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: 2. If force F is to have a component along the u axis of Fu = 6kN, determine the magnitude of F and…

A:

Q: FAND e Canrid 35 300 SECTION MODULUS , Sx, S O radius of giyntion, rx RuF DMEHSIONS '.RE IN MM. I O…

A: As per guidelines one need to solve only first 3 subparts

Q: Answer the following

A: Given data The initial temperature of the bar is T1=72°F The final temperature of the bar is T2=0°F…

Q: 2-Most of the pressure reading over the upper side surface are negative, Explain.

A: To explain: 2-Most of the pressure reading over the upper side surface are negative, Explain.

Q: instantaneous discharge velocity

A: Given; Large tank with a nozzle attached contains three immiscible,   inviscid fluids as…

Q: Solve it with ID number = 250

A: Find the minor and friction losses.

Q: The three flat blocks are positioned on the 30° incline as shown, and a force P parallel to the…

A: Given:-Block 1=30 kgBlock 2=50 kgBlock 3=40 kgθ=30°For 1 and 2, μs=0.30For 2 and 3, μs=0.40For 4 and…

Q: 5. Steam at 7 bar and 250 °C enters a pipeline and flows along it at constant pressure. If the steam…

A:

Q: 1. What are the procedures on how to calibrate a water tank? (At least 10 steps) 2. What are the…

A: 1) To find: The procedures to calibrate a water tank.

Q: 4-The fluctuation in pitot tube reading during velocity distribution experiment is due to

A: As per the answer asked only for the question No 4. So here is the answer for Q.4. Pitot Tube: In…

Q: 4000 N --- Figure 2

A:

Q: determine the tension in cable AC and in cable BC.

A:

Q: 1. Determine the component of each force along the specified x - y axes. Refer figu 1. the exclusive…

A:

Q: Determine the reactions at the supports. 5 kN/m 12 kN Figure 1 4 m 2m 2 m

A:

Q: 53. An 8.00-L sample of gas at 99.0 kPa and 25 deg C is compressed. What is its final pressure at 25…

A:

Q: 3. A REVERSED CARNOT CYCLE IS USED FOR REFRIGERATION AND REJECTS 200 000 Btu/min OF HEAT AT 152.6F…

A: GIVEN DATA- Q2=200000 Btu/min TH=152.6'F TL=450.6'R WE HAVE TO FIND COP , CAPACITY , WORK

Q: Consider the simple beam in Figure 7 with two concentrated loads, where AB-BC=CD=4m: 6kN 12kN 12m…

A:

Q: can the solve the last three quetsions please

A: mass of refrigerant R-22, m= 2kgThe initial pressure, P1= 6.8 barThe initial state is saturated…

Q: 3. A light bar AD is suspended from a cable BE and supports a 50 – lb load block at C. as shown in…

A:

Q: Answer the following

A: Given, E=30,000,000 psi, G=11,500,000 psi

Q: The figure below shows a vapor power cycle that provides process heat and produces power. The steam…

A:

Q: Please answer the following

A: Given data DAB=30 mmDBC=46 mmdAB=10 mmdBC=25 mmTAB=10 N·mTBC=20 N·m

Q: 3. Determine the components of force F along the x - y axes which are parallel and perpendicular to…

A:

Q: 6. 0.05 kg of steam at 15 bar is contained in a rigid vessel of volume 0.0076 m³. What is the…

A:

Q: QUESTION 4 spring-1 Unknown mass, wwwmf attached to the free end of a spring (the other end of the…

A: Given data  f1= 5.883Hz f2= 4.222Hz Find the value of frequency (f).

Q: The 0.25 kg slider A is pushed along the circular bar by the slotted bar. The circular bar lies in…

A:

Q: Question 3a) 3 decimal points in inches * Locate the centroid of the shaded area а) х-ахis b)y-аxis…

A:

Q: Question 7a) 3 decimal points in meters * A bullet is fired at an initial velocity of 150 m/s and an…

A:

Center of Gravity and Centroid

The term center of gravity indicates the position or location of a point about which the whole weight of a body or system is supposed to be concentrated, which means the whole weight of the body or system works through this point. It is closely related to mass distribution. For all positions of the body, the center of gravity would be a single point.