5. Compute the force necessary to move a 6000 lbs supported on four wheels of 2.5 ft diameter, assuming the coefficient of rolling friction to be 0.007.

Q: Prob # 9. Find the horsepower transmitted by a pair of friction wheels, the diameter of driving…

A:

Q: The 60° V-belt of a machine is pass around the pulley A of a motor and over a pulley B as shown in…

A:

Q: A weight of 200lbs. rests on an inclined plane that makes an angle of 35° with the horizontal. If…

A:

Q: a 2kg book is pushed against a vertical wall by a horizontal force P. The coefficient of friction…

A: As per given question A 2kg book is pushed against a vertical wall by a horizontal force P. The…

Q: Find the magnitude and direction of the minimum pull required to haul a mass of weight 120N up a…

A:

Q: Find the value of coefficient friction if friction force is 222 N and Normal force is 1000 N

A:

Q: Work Example 8.1 on page 390 of your textbook, but replacing the book values with the following…

A:

Q: Two identical pulleys with diameter of 711 mm, are mounted on two parallel shafts for flat belt…

A:

Q: 2. A 200 lb block rests on a horizontal surface. The coefficient of static friction between the…

A: Given   Mass, m = 200 lb                 = 90.71 kg    Friction = 0.35 Find   Force, P

Q: From the rotating shaft shown below, a force 100 N was pulled to reduce the shaft’s angular speed…

A:

Q: belt engages the smaller pulley horizontally. It is understood that the tension in the slack side of…

A: Draw the diagram of the driver and driven pulley without the jakey pulley,

Q: The pulley of Fig. wheel that fits loosely over a t in.-diameter shaft. A rope passes over the…

A: Given: The diameter of the wheel, D = 4 in The diameter of the shaft, d = ½ in The magnitude of…

Q: ** Please label the question answers so I could understand it better! Thank you! Scenario: A chair…

A:

Q: Find the value of coefficient friction if friction force is 222 N and Normal force is 1000 N

A: Given data : Friction force=f Normal force=F'   Required : Coefficient of friction

Q: Find the friction force if coefficient of friction 0.3 and normal force is 120 N

A: Given data : Coefficient of friction=μ Normal force=N   To find : Friction force

Q: 4.) A flat belt makes contact with an 18 in. diameter pulley through half its circumference. If the…

A:

Q: A flat belt is wrapped around a Ø3.00-inch pulley for 217°. The loose side belt tension is 282 lb…

A:

Q: (A) If the power losses in Pelton wheel due to bucket friction is given by 1 POK (V, -u) where K is…

A:

Q: A pull of 20 N at 30° to the horizontal is necesary to move a block of wood on a horizontal table.…

A:

Q: Two parallel shafts whose centre lines are ‘5’ m apart, are connected by an open belt drive. The…

A: C=5 mD=3 md=3 mTmax=4 KNμ=0.3N=700 rpmVelocity of belt, V=π*d*N60V=π*3*70060=109.95 m/s

Q: The effective pressure on a 400 mm diameter piston is 1.1 MN/m² when the crank is 32° beyond top…

A: Given: Diameter of the piston→D=400 mm=0.4 m So area of the piston→A=π4×D2=π4×0.42=0.125 m2 Pressure…

Q: a 200N black is at rest on a 30° incline the coefficient of friction (0.2) compute the value of a…

A: Given,  Weight of the block , W = 200 Angle of inclination , θ = 30 Coefficient of friction ,μ =…

Q: Find the coefficient of friction if friction force is 723N Normal force is 823 N

A: Given data : Normal force=N Friction force=F   Required : Coefficient of friction

Q: Q2. Each of the two blocks in Figure 10.4 has a mass of 10 kg, and the coefficient of friction…

A:

Q: A cylindrical roller 300mm diameter and a mass of 50kg. rest on a horizontal floor with its curved…

A: Given data: Mass of the roller, m = 50 kg diameter of the roller, D = 300 mm  radius of the roller,…

Q: A uniform push of 150N, applied at an angle of 30 degrees to a 20kg block which rests on a…

A: Given data: Initial velocity of block, u = 0 m/s. Final velocity of block, v = 6.5 m/s. Time, t = 4…

Q: Determine diameter of hand-wheel or length of handle, assuming that maximum force exerted by a man…

A: Given, Force exerted by a man, F=150lbf Force need to be applied, P=6000lbfCorfficient of…

Q: . A block weighing 400 N is pulled along a level from at a constant speed by a rope which makes 40°…

A: Ans: 0.42 Option (b) is correct.

Q: QI-A 75-Kg man wants to pull a 145- Kg box and the coefficient of static friction between the box…

A:

Q: (i) A uniform ladder of length 7 m rests against a vertical wall. It makes an angle of 45° with the…

A: Q. 3(i), Given: Length of the ladder=7 m angle=45o coefficients of friction between the ladder and…

Q: A rope is hung over a stationary drum with weights on each end (100N; 400N). The rope is just on the…

A: given data : F2= 400 N F1=100 N the rope is just a point of slipping θ= 180 degreeswe need to find…

Q: A force of 347 N is exerted on a box of 5 kg on the floor. If the coefficient of friction is 0.37,…

A: As per given question  Given data  F=347 N Mass = 5 kg Coefficient of friction =0.37 We have to…

Q: t force that will hold the body.

A: Given:W=500 Nθ=150°μ=0.3

Q: While a vehicle with a mass of 2350 kg is moving at 120 km/h, suddenly braking It stops with an…

A:

Q: n a belt arrangement two pulleys are connected by flat belts having same diameters. The maximum…

A: Since the two pulleys are connected by flat belts, therefore, the lap angle is 180 degrees.

Q: Find the value of coefficient of friction if friction force is 200 N and Normal force is 780 N

A:

Q: 1. The blocks shown are connected by flexible, inextensible cords passing over a frictionless…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.