5. An impedance coil is connected in parallel with a capacitance C of 12.5 µF. The inputvoltage to the circuit is 100 V at 31.8 Hz. The phase angle between the two branchcurrents (Ih and la) is 120° and the current in the first branch is l; = 0.5A. Determine thefollowing:a) the current a and total currentb) the value of R and X.c) the value of inductor (L in mH)dj the total impedancee) the power factorf) the value of conductance (G in mu) and susceptance (B in µU)9) total admittanceIT12100 V: = 12.5 µFl1 = 0.5 AXL

Nodal Analysis - It is used to find node voltage using Kirchhoff's current law. Kirchhoff's current…

5. An impedance coil is connected in parallel with a capacitance C of 12.5 µF. The input voltage to the circuit is 100 V at 31.8 Hz. The phase angle between the two branch curents (lh and l2) is 120° and the current in the first branch is li = 0.5A. Determine the following: a) the current a and total current bị the value of R and X. c) the value of inductor (L in mH)

5. An impedance coil is connected in parallel with a capacitance C of 12.5 µF. The input voltage to the circuit is 100 V at 31.8 Hz. The phase angle between the two branch curents (lh and l2) is 120° and the current in the first branch is li = 0.5A. Determine the following: a) the current a and total current bị the value of R and X. c) the value of inductor (L in mH)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A 15µF capacitor and a 470 ohm resistor are connected in series with a function generator. The supply voltage is 50V RMS 40Hz. Find the reactive power for this circuit.
or the coupled circuit shown in Figure 3, find the voltage across the capacitor of -j1092 reactance with Vi=1020° V and V2=10290° V? j20 www www 50 50 V₁ 5 100 Figure 3 5 V₂
An electrical engineer is working with a parallel AC circuit. The circuit draws 8 ohms on a resistive branch, and the angle of the total impedance is 35°. What is the approximate number of ohms on the inductive branch? O 0.7 O 4.59 O 5.6 O 6.55
An impedance coil absorbs 250 W when connected across 220 V, 60 Hz mains. It is then connected across 110V 25Hz mains and also absorbs 250 W. What is the inductance of the coil? a. 0.125 H b. 0.149 H c. 0.154 H d. 0.163 H
A capacitor of reactance 50 n and a resistor of 40 Q are connected in series across the AC source. What is the phase angle difference between the total voltage and the current in the circuit?
I am getting the output of the clamper circuit wrong, how will this circuit be output ? circuit question : Set the input voltage signal to a sinusoid with 100 Hz frequency and 20V peak-to-peak amplitude with C=1μF. Obtain and plot the input and output voltage waveforms.
i need the answer quickly
An inductive impedance made up of a resistor and an inductor has the characteristic that its currentadvances in phase to the voltage at the impedance A) lags in phase with the voltage across the impedance B) is in phase with the voltage across the impedance. C) None of the above
A 206.0-2 resistor and a 2.80-µF capacitor are connected in series across the terminals of a sinusoidal emf with a frequency of 150 Hz. The inductance of the circuit is negligible. What is the impedance of the circuit?
find the imaufitetd ciruit covraiuinga open sesistance of capacitor of 100 series inductance 04 D.15H and a connected in 122 ano micron farad ate 100 Vp so Hž supply.caleulate the total inpedance, the cireuits cument and vottage acro a auos each element
Calculatethe Value of the Capaeitance at resanamce if w-SooD rad/Seea.k or6 齐

4. For the given circuit for a 20 V sinusoidal input v, what is the value of v, at which the clipping begins? peak V-5V a) 5 V b) 0 V c) -5 V d) Clipping doesn't occur