5. ( After surveying a construction site, the surveyor produced the following grid below. If you consider 1.0 ft as the proposed elevation that you can cut to. What is the total cut volume (cy) available if you used grid method to calculate the excavation volume? Cut 2.1 ft 30 ft Cut 3.5 ft 30 ft Cut 3.2 ft Cut 1.2 ft 30 ft Cut 4.6 ft

5. ( After surveying a construction site, the surveyor produced the following grid below. If you consider 1.0 ft as the proposed elevation that you can cut to. What is the total cut volume (cy) available if you used grid method to calculate the excavation volume? Cut 2.1 ft 30 ft Cut 3.5 ft 30 ft Cut 3.2 ft Cut 1.2 ft 30 ft Cut 4.6 ft

Fundamentals Of Construction Estimating

4th Edition

ISBN:9781337399395

Author:Pratt, David J.

Publisher:Pratt, David J.

Chapter4: Measuring Site Work, Excavation, And Piling

Section: Chapter Questions

Problem 8RQ

See similar textbooks

Similar questions

Assume a new elevation of 100FT across the entire site. Existing elevations are as written on the attached grid. Using the grid method, calculate the amount of cut, fill, and either excess or shortage of material. Grid Size: 10'×10' Complete the spreadsheet with the following information. Station New Elevation Existing Elevation Depth Cut Depth Fill Frequency Quad Area Constant Volume Cut Voulme Fill 1A 1B 1C 1D 1E 1F 1G 2A 2B 2C 2D 2E 2F 2G 3A 3B 3C 3D 3E 3F 3G 4A 4B 4C 4D 4E 4F 4G 5A…
The table below gives area information on earthwork of road cross sections at three different stations. The cumulative amount of earthwork moved from station to station is most nearly: Station Sta 5 + 00 Sta 6+35 Cut (ft?) Fill (ft?) 60 80 120 150 Sta 8 + 65 200 210 O 2100 yd3 3921 ya O 1813 yd O 2931 yd
Subject: Surveying 1.3 Please show your correct/detailed solution.
Q1)In the shown drawing, a grid area of 50 m X 50 and the grid elevations are provided. a- Calculate the average level which the land can be leveled without cut or fill? b-If the land area must be leveled to a level of 100m, calculates the cut or fill needed for the land? 97.6 97.6 97.4 97.2 98' 98.5 98.6 98.2 97.7 150' 99 99.3 99.4 99.5 99.0 100 100.3 100.4 100.6 100.4 150
A 20m x 20m grid is set out over a T shaped section. Levels are taken on teh grid, and RLs calculated, as below: 425.2 424.7 424.7 423.4 425.3 423.8 424.4 425.1 424.3 424.7 424.2 423.8 If the area is then to be excavated to RL 421.0m, calculate the volume of cut using the grid levelling formula. Volume of cut:
Given the following cross-section notes for a road grading work. The roadbed is 9m wide and the side slope for cut is 1:1 and for fill is 1.5:1. Determine the area of cut of the section. +1.2 +1.2 -3.2 +2.8 X1 3.5 X2
Q5A)The figure below represent a grid for a parcel with (25 m x 25 m) sub-grid dimension Draw the contour line with elevation=40 00 m using a horizontal scale =1/500 33.14 m 42.24 m 32.22 m 35.74 m
Why do construction surveyors usually provide offset stakes?
The areas of cut of two irregular sections 60 m apart are 32 m^2 and 68 m^2 respectively. The base width is 8 m. with a sideslope of 1:1. Find the volume using end area method in cubic meter. (Type your answer in whole number, numerical value only, no need to include the units).
Explain needle-punching procedure in geotextiles.
List and describe briefly the steps in making a triangulation network.
Given the following information on the sketch, compute the following: Coordinates at C, distance AC, bearing (RAD PT) to C. A N=846.05 E=486.18 $30 47'11'E C 100 Coordinates of C: N= Distance AC = PL 2 Bearing (RAD PT) to C=_ PL R=384.30 RAD. PT N=356.58 E=1097.54 E=