5. A two wire DC distributor 0.8 kilometre long is supplying two loads 10A and 20A at 500 meter and 800 meter respectively as shown in Figure B4. 250V DC b- a 500 meter 300 meter Resistance of line 0.2 ohms/km 10A 20A Figure B4 Estimate: i. Total Voltage drop ii. Voltages at points b and c iii. Voltage regulation

Q: example open loop system

A: In this question we discuss about open loop system

Q: Q4: A power distribution station consisting of 100KVA, 4500V/225V, and 50 cycles per second…

A: In the given scenario, single-phase transformer is used. The EMF equation for the single-phase…

Q: The recommended limit of voltage drop on a power circuit for a single-phase supply as per IEE Wiring…

A: The explanation is as follows.

Q: What is load line and what is duty cycle?

A:

Q: What is the maximum current-carrying capacity of a wire or cable? A. Overcurrent B. Energy C.…

A: The objective is to determine the correct term for the maximum current capacity.

Q: the busbars of a power station are in two sections a and b separatedvby acreactor. connected in…

A:

Q: GMR calculate

A: Step 1:Step 2:Step 3:Step 4:

Q: 5. Atwo wire DC distributor 0.8 kilometer long is supplying two loads 10A and 20A at 500 meter and…

A: Note: Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question…

Q: Answer whether each of the following questions is (True) or (False)? Write the true answer if it is…

A: Phasor diagram is widely used to represent various quantities in electrical circuits.

Q: Figure B2 shows an HVDC system connecting the 400 kV electricity networks of two countries (System A…

A: HVDC System Analysis problem step-by-step and solve each part like this one. Part (i) - Transformer…

Q: We wish to connect a 6 kVA, 120/240 V transformer as an autotransformer to a 120 V source to supply…

A: "Since you have posted a question with multiple sub parts we will solve first three subpart for you…

Q: What are FACTS (Flexible Alternating Current Transmission Systems), and how do they improve the…

A: Flexible Alternating Current Transmission Systems (FACTS) are a set of advanced power electronics…

Q: Diagram of Cooling of dry type transformers

A: It is asked to draw the diagram of cooling of dry type transformers.

Q: PROBLEM SOLVING NO. 2: A string of suspension consists of four (4) units. The Voltage between each…

A:

Q: Single core cable design for 25 kV. The radius of conductor is 0.5 cm. The insulation material…

A: we know that electrical gradient in a cable is given by g=Vx ln R2R1

Q: L-type equivalent circuit and parameters for a continuous sinusoidal phase of a 5.5 kW, 1450 rpm,…

A: According to the context of the given question, it is required to determine the number of times…

Q: Briefly explain about single phase and three phase power supply with diagrams.

A:

Q: What is a FACTS (Flexible Alternating Current Transmission System) device, and how does it impact…

A: A Flexible Alternating Current Transmission System (FACTS) device is a system composed of static…

Q: Describe the concept of HVDC (high-voltage direct current) transmission and its applications in…

A: The student is asking to describe the HVDC in transmission of power?HVDC, or High-Voltage Direct…

Q: The single line diagram of a power system is shown in Figure Q2.1 including generator and…

A: Given length of line =50 km MVA base = 100 MVA For line , base voltage =11 kV

Q: Single core cable design for 25 kV. The radius of conductor is 0.5 cm. The insulation material…

A: electrical gradient in a cable is given by  g=potentail differnecex lnR2R1   = Vx lnR2R1

Q: Q4 (a) Define three (3) advantages of alternating current (AC) for long distance power transmission…

A: “Since you have asked multiple question, we will solve the first question for you, here it is Q4. If…

Q: What are FACTS (Flexible Alternating Current Transmission Systems) devices, and how do they enhance…

A: Flexible AC Transmission Systems (FACTS) devices are a family of power electronics-based devices and…

Q: What are the key factors that influence power quality in electrical grids?

A: Power quality refers to the characteristics of electrical power as it is delivered to consumers.…

Q: Q4) A 2-wire d.c. distributor cable AB is 2 km long and supplies loads of 100A,150A,200A and 50A…

A:

Q: One advantages of load balancing is that each phase conductor carries the ? current value

A: We need to tell about advantage load balancing is that each phase conductor carries the equal…

Q: A two wire DC distributor 0.8 kilometer long is supplying two loads 10A and 20A at 500 meter and 800…

A: The distribution system in power system has variable loading along it's length. There are tapping at…

Q: A three phase,Y connected, 215 V (line to line), 7.5 kW, 60 Hz, three pole IM has the following…

A:

Q: induced emf is equal to rate of change of magnetic flux. 4.a- According to 4.b- In a 3-phase, 4…

A: We need to select correct option for given statement

Q: "What will be the frequency (in kHz) of transient and peak restriking voltage (in kV) repectively

A:

Q: Transmission and distribution lines are important components of any power system study. Aluminium…

A: The explanation is as follows.

Q: Where does Wye-Delta circuit used in industry application? What specific application and explain

A: Given  We need to enumerate where does Wye-Delta circuit is used in industrial application. Please…

Distribution System

The final stage in the delivery of the electric power is the electric power distribution system. From the transmission system to the individual customers it carries electricity. The distribution system is connected with the transmission system and is used to lower the voltage of the transmission to medium voltage in the range of 2 kV to 35 kV with the help of transformers. This medium voltage to the distribution transformers located near the customer's premises is carried by the primary distribution system lines. These distribution transformers in turn lower the voltage to utilization voltage used in lightings, household appliances, industrial equipments etc. Through secondary distribution lines often several customers are supplied from one transformer. It is through service drops, the commercial and residential customers are connected to the secondary distribution system lines. Customers who demand a larger amount of power can be connected directly to the primary distribution system level or the sub-transmission level.