5. A 45 tonnes capacity compound NH, compression system with water intercooler after low pressure compressor and liquid flash chamber has condensing pressure 14 bar. Evaporator pressure is 1.3 bar and intercooler and flash chamber pressure of 5 bar. Volumetric efficiency of both the compressors is 85%. Ammonia is cooled to 32°C in water intercooler and liquid NH, is cooled to 30°C in the refrigerant vapour heat exchanger. Assume both the compressions are isentropic and low pressure compressor gases are directly taken to the H.P. compressor after intercooling. Find the following: (i) Ammonia passing through evaporator per minute (ii) (iii) Ammonia passing through H.P. compressor per minute Total power required to run the system (iv) COP of the system (v) L.P. compressor displacement per mint Draw flow diagram for the system and represent the processes on p-h chart.

5. A 45 tonnes capacity compound NH, compression system with water intercooler after low pressure compressor and liquid flash chamber has condensing pressure 14 bar. Evaporator pressure is 1.3 bar and intercooler and flash chamber pressure of 5 bar. Volumetric efficiency of both the compressors is 85%. Ammonia is cooled to 32°C in water intercooler and liquid NH, is cooled to 30°C in the refrigerant vapour heat exchanger. Assume both the compressions are isentropic and low pressure compressor gases are directly taken to the H.P. compressor after intercooling. Find the following: (i) Ammonia passing through evaporator per minute (ii) (iii) Ammonia passing through H.P. compressor per minute Total power required to run the system (iv) COP of the system (v) L.P. compressor displacement per mint Draw flow diagram for the system and represent the processes on p-h chart.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: This still doesnt answer how to get points 2, 2', and 1', so how did you get it?

A: Itis asked to explain how the state points 2, 2' and 1' are obtained

Q: How much will an air leak cost during three monthes? the hole has a diameter 6.35mm at line pressure…

A: Given Hole diameter D=6.35 mm Line Pressure P= 690 kPa Electricity Cost C=7 centskwh Time of air…

Q: 2. Draw the sketch of 'Drilling machine' and explain any four parts. Use pencil to draw the neat…

Q: how o create all parts list after the drawing ?

A: Given question: how to create all parts list after the drawing ?

Q: 2. Write 5 details found on the drawing title block?

A: The bottom right hand corner block in engineering drawing sheet is known as title block. This block…

Q: 5- HB Pencil is used to fill the sheet table. O True O False 2- Choose the correct answer: Oa- A3…

A: 5. HB pencils are used in a sheet because it gives dark mark to identify the sheet table so the…

Q: I need answers to this part, thank you.

A: The correct matches are:

Q: For #16.6 on page 669, do the followings: 1) Draw the top, the front, and the right-side…

Q: Are you able to show an answer in terms of using formula from start to finish to get the answer…

A: Are you able to show an answer in terms of using formula from start to finish to get the answer…

Q: 8. A note in the comment section of a title block mentions that all faces should have a +.10…

A: Circularity (roundness) tolerance is 2-D in nature.

Q: Q3: Mark the Following True or False 1. Hidden lines are used in sectioned area when they are needed…

A: 1.TRUE 2. TRUE 3.TRUE 4.FALSE 5. FALSE 6.FALSE 7.TRUE 8.FALSE 9.FALSE 10.FALSE 11.TRUE 12.TRUE…

Q: Give one problem solving question about "Method of Sections" and show the solution

Q: Circle all correct statements. Plastic deformation a. Is permanent. b. Is recoverable. c. Can be…

A: Dear student, we are suppose to solve only one question. Please post other question as a separate…

Q: can you please write it in a proper way?

Q: _1. He is an English man credited for the invention of a screw cutting lathe. _2. A man from New…

A: Identification test :

Q: organize the answers pls.

Q: 1.00 1.38 3.38 38 2.00

A: Select the correct statement about the notation circled in green and marked as letter D. Assume all…

Q: This is no answer sorry the answers are offered A B C or D

Q: A piece of 12-gauge sheet metal is 7⁄64 inch thick. A stack of sheet metal is171⁄2 inches thick. How…

A: Given12 guage sheet metal sheet thickness t=7/64 inchthickness of stacked sheets t2=171 2inches

Q: Please give the answer as in the format asked

Q: Write the types of keys and sketch freehand of them with dimensions and equations.

A: A key is a machine element that is fitted in the axial direction with the mating parts in pulleys…

Q: Whats the final answer if it requires the final answer in newton?

A: We have-a) The moment at point O is 100.56 lb-ft (counter clockwise)b) The magnitude of the…

Q: PART VI. Given that f(x,y) = (x +y)/2k, where x=-1,1,2 and y= 0,2,4 1. Find k 2. Find the marginal…

Q: Please answer questions 7,8, show reasons and examples

A: The characteristic equation of the system is:x^6 + (73*x^5)/40 + (1969*x^4)/48 + (22309*x^3)/600 +…

Q: the isometric drawing has to be in 30 degree angle or vertical

A: It is asked to describe whether the isometric drawing has to be at 30 degree angle or vertical

Q: I need answers for 7,8, and 9,

A: A 0.250”X0.250” square hole.

Q: Part C - Maximum allowable axial force for fixed-and-free-end support If the cylindrical column is…

Q: A specialty coffeehouse sells Colombian coffee at a fair rate of 300 kilograms annually. the beans…

Q: Please give the details explanation of the answer

Q: I don't understand due to the way its written, can it be written again but more clearly pls

A: From the question, the given data are: Volume of heater = Capacity of heater =V1 = 2 liters = 2 x…

Q: That is the answer I have and it is marked as wrong, could you please do it again and see if you get…

Q: Quenching is a process that can reduce the grain size and form a lot of grain boundaries in the…

A: Quenching: In this process metal is heated above its recrystallization and than cool it rapidly. The…

Q: With reference to the drawing callout in Figure 4 below, which part(s) would 'pass' or 'fail'…

Q: Problem A solid uniform ball with mass m and diameter d is supported against a vertical frictionless…

Q: You've been asked to design a stamping tool as shown. What are the internal forces at A and B? Ans:…

A: Draw FBD of the given system

Q: 10) Define the slip angle.

A: The angle between the direction of the wheel in which it is pointing and the direction in which it…

Q: Write legibly and box the final answer

Concept explainers

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing. 

Question

I need answer in handwritten

5. A 45 tonnes capacity compound NH, compression system with water intercooler after
low pressure compressor and liquid flash chamber has condensing pressure 14 bar.
Evaporator pressure is 1.3 bar and intercooler and flash chamber pressure of 5 bar.
Volumetric efficiency of both the compressors is 85%. Ammonia is cooled to 32°C in
water intercooler and liquid NH, is cooled to 30°C in the refrigerant vapour heat
exchanger. Assume both the compressions are isentropic and low pressure compressor
gases are directly taken to the H.P. compressor after intercooling. Find the following:
(i) Ammonia passing through evaporator per minute
(ii)
Ammonia passing through H.P. compressor per minute
(iii)
Total power required to run the system
of the system
(iv) COP
(v) L.P.
compressor displacement per mint
Draw flow
diagram for the system and represent the processes on p-h chart.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

What is an inflection point?
ADVANCED CHEMISTRY! RATE WILL BE GIVEN! PLEASE WRITE THE COMPLETE SOLUTIONS A Steam at 400 deg C an 8,200 kilo Pascals enters a turbine and leaves at 10 kPa. What is the entropy of the leaving steam if the efficiency of the turbine is 0.76. Round the answers in to 2 decimal places. Hint: Turbine's efficiency is the ratio of work delivered by the actual turbine to the work delivered by an isentropic turbine (no entropy change) H (kJ/kg) S (kj/kg-K) 8200 kPa, 400 degrees 3137.6 6.3534 10 kPa, sat. liquid 191.832 0.6493 10 kPa, sat. vapor 2584.8 8.1511
You are a mechanical engineer tasked with overseeing the equipment used in constructing a high-rise. A tower crane, used to lift and move heavy construction loads, is being used in the construction site.
I asked for problems 6 and 7 to be answered, but I did not get a properly structured answered as the example shows on problem number 1. Here is the link to the questions I already had answered, could you please rewrite the answer so its properly answered as the example shows (Problem 1)? https://www.bartleby.com/questions-and-answers/it-vivch-print-reading-for-industry-228-class-date-name-review-activity-112-for-each-local-note-or-c/cadc3f7b-2c2f-4471-842b-5a84bf505857
follow up question - for the past two question. (subquestions)
HANDWRITTEN. answer 4 5 6 then box the final answers
A sprinter practicing for the 200-m dash accelerates uniformly from rest at A and reaches a top speed of 36 km/h at the 76-m mark. He then maintains this speed for the next 61 meters before uniformly slowing to a final speed of 31 km/h at the finish line. Determine the maximum horizontal acceleration which the sprinter experiences during the run. Where does this maximum acceleration value occur? Part 1 Answers: (a) al- Finish line Calculate (a) the magnitude of the tangential acceleration near start of the race and (b) the magnitude of the tangential acceleration near the end of the race. (b) lal- i 0.658 i 0.205 m/s² 39.9 m m/s² A Save for Later Last saved 12 minutes ago. Saved work will be auto-submitted on the due date. Auto- submission can take up to 10 minutes. Attempts: 0 of 3 used Submit Answer Part 2 The parts of this question must be completed in order. This part will be available when you complete the part above.
How did you get 4/5 and 3/5?
Please provide more details for question b and c. thank you
Please the answer provided is not clear, some words and letters not clear, can you please type the answer or write clearly so that I can see
i need clear ans and solve very very fast in 20 min and thank you | DYBALA A part under forming force showed that 15% decrease in thickness and 10% increase in width, find the change in length (sign and value) if initial length is 200 mm?
! Draw a sketch of the above drawing in A3 (or two A4 paper taped together).