5 KN 30 10 kN 10 KN с 1.90 B 5 SAN 15 AN 10 KN 90% E F 30

Q: If you know traction (stress vector) acting on N planes through a point, you can find traction…

A: Solution:   For the proper explanation, we need to understand Cauchy's law. According to this law, a…

Q: A R₁ Find R1 and R2 reactions in kg. 1000 kg. 400 kg BY 3m 1.5m 6m to C 1.5m D R₂

A: Note: As mentioned in the question, all forces are considered in kg and not in N. Here, Length of…

Q: Q) Consider a weight supported by a cable as shown in figure below is equal 100 kN. Determine the…

A:

Q: From the figure below, choose the correct answer of the following 6 kN 5 kN 3kN 30° 0.2 m 4 В 2 m- 4…

A: Mechanical Equilibrium: A body is said to be in mechanical equilibrium if it satisfies the following…

Q: Two tension forces are applied to the top of the tower as show wire is also attached to the top of…

A: Given data is We have to find the Tension in the wire AB such that the resultant force is only in…

Q: A reservoir of oil has a mass of 830 kg. The reservoir has a volume of 0.920 m³. What will be the…

A: Given Data M=830 kg V=0.92 m3

Q: 160 N 200 N 30- 100 nun 200 min 30 150 N A

A:

Q: Find the representation of the shown force victor F along the pipe OA, given F= 500N 5m 7 m 6 m B 5…

A:

Q: Q/ Compute the tension (T) in 1: the cable? Neglect the friction between the cable and the pulley.

A: Given

Q: I. A steel rod is acted upon by the loading shown below. 50 mm² is the area of the circular rod. The…

A: Given data  Area of cross-section (A) = 50 mm2 Est = 200 GPa   To determine a) Force in segment AB,…

Q: A force P = 5Bi + 3Bj + 7Bk)lb has a positive x component of 200 lb. Write the force P in vector…

A: A vector is written as P→ = Fxi^ + Fyj^ + Fzk^ where, Fx, Fy and Fz be the forces in x,y and z…

Q: Q1.) A cable system is subjected to three concentrated loads as shown. The sag at point D is…

A: To Find:The sags and .The section of cable supports the largest tension and the magnitude.Given:A…

Q: Q3/ For the figure below: a) The total area is: 2 6"

A: Given:   To determine the total area and the centroid of the given composite figure.

Q: The magnitude of horizontal components of reaction on the member at the pin B is.. -2.5

A: Given Data→ Beam

Q: Q.1 (a) Express the following unit with an appropriate prefix (i) (100 cm) (0.5 mN)² (ii) 50 kN³/100…

A: “Since you have posted multiple questions with multiple sub parts, we will provide the solution only…

Q: 11. A cantilever beam is subjected to three vertical forces and a moment as shown in Figure 11.…

A: “Since you have posted multiple questions, we will provide the solutiononly to the first question as…

Q: What is the algebraic difference between the lowest limit of size dmin and the nominal size da (dmin…

A: The correct option is 4 (the lower deviation ei), Lower deviation is the algebraic difference lower…

Q: 2L Answer: DI = B 4 m 2L i 3L D 4 m m 2L E H 2L AB=BC=CD=DE = EF = FG L F 4 m

A:

Q: The stress-strain diagram for a polyester resin is given in Figure 2. The rigid beam AC is supported…

A:

Q: 1.5 m 1.0 m A B 3.3 m FIGURE P1.10 C 15 kN 12 kN

A: Considering that you want to know the forces in the members.Thus the reaction forces are as shown…

Q: Solve for Support reactions (A and B)

A: Given The intensity of the uniform distributed load w= 7 KN/mThe length of the uniform distributed…

Q: Q1: Calculate the moment of the 0.4 kN force about point O. A et Ww a ana Va y nor de faliatea hanc…

A: Given Data P=0.4 kN

Q: The free body diagram of a rigid body shows O forces O moments support reactions All of these

A: Given data: -  The force F1 is F1 = 6 kN. The force F2 is F2 = 3 kN. The force F3 is F3 = 5 kN.

Q: 2. A MATHaling.com Ax 2 m 2 m C 2 m 200 N 100 N Ay Figure 1:

A: For solution refer below images.

Q: 6 ft y 9 + B E 4 ft- D H -4 ft 4 ft K +ft- G 3000 lb 1000 lb X

A: Given: Force applied at point H: →FH=3000 lb    (in downward direction) Force applied at point G:…

Q: 60° looks 50 g C 80° 6 G 30 VO 38 66 f 7 ft 78 ) ។ Yo >15 3ft 4ft 2ft Find force for all member? E

A: