5-In an experiment for determining the breakdown voltage of transformer oil, the following observations were made. Determine the power law between the gap spacing and the applied voltage of the oil. Gap spacing (mm) Bd. voltage (kV) 10 86 148 169 219 100 50 24.5 10 234567891014 20 Gas spacing dimm) Ans (Vb 32.6 d 0.84 )

5-In an experiment for determining the breakdown voltage of transformer oil, the following observations were made. Determine the power law between the gap spacing and the applied voltage of the oil. Gap spacing (mm) Bd. voltage (kV) 10 86 148 169 219 100 50 24.5 10 234567891014 20 Gas spacing dimm) Ans (Vb 32.6 d 0.84 )

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

6. Identify the electronic symbol pointed by the line in the given schematic diagram F A TIP2066 with Heat Sink MA 01 Ohm E Sw TIP2055 wih Heat Sink B 10 Amp 50 PN Bridge Rectiter 0.1 Ohm SW LMTar2 we Heat Sink FUSE A FUSE 10A 230 Voit AC 12V Out o Gnd in 0.1 Ohm Sw 470uF 230112V 10A Transformer 47000UF Sov Output 10 uf 12V10A D A В C D F M CnolIL Choclk
How does the coupling factor affect the primary and secondary voltages? For example if the turns ratio in my transformer is 1:2 and the Vin is 10V, the voltage on the primary side is 10V and the voltage on the secondary side is 20V when the coupling factor (k) is 1. What will the primary and secondary voltages be if the coupling factor becomes 0.5?
A 200 V/100 V, 50 Hz transformer is to be excited at 40 Hz from 100 V side. For the exciting current to be constant, the applied voltage should be ?
The rated power of a certain transformer is 1 kVA. The transformer operates at 60 Hz and 120 V ac. at 60 Hz and 120 V ac. The secondary voltage is 600 V. (a) What is the maximum current at the load? (b) What is the smallest RL value that can be excited? (c) What is the largest capacitor that can be connected as a load?
A Buck converter has an output power of 1950 Watts, and a source voltage of 1000V (the constant DC voltage). Using the information provided and the "“transformer-like" relationships derived in class, estimate the corresponding load currents for the following duty ratios: a) D=0.35 b) D=0.9 c) D=0.5
Vin V₁ leee V₂ R₂ Vout 1:5 Assume the transformer circuit above is ideal, and that R₁ = 100, R₂ = 400 and 11,rms = 50 A./ Find the rms current, 12,rms, flowing thru the secondary side of the transformer. 12.rms [A]
Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across R, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diodeshave? (Use constant voltage drop model for the Silicon diode) D IN4001 OV 10 kN IN4001 DELL
In a transformer that has 10 times more turns on the secondary side (side 2) than on the primary side (side 1), the magnitude of the voltage/EMF across the windings on the secondary side, E₂ will be... O a.... 10 times lower than the voltage/emf on the primary side, E₁. O b.... the same as the voltage/emf on the primary side. O c.... always zero regardless of the voltage on the primary side, E₁. O d.... 10 times higher than the voltage/emf on the primary side, E₁.
9. Electrical transformer is shown on the figure bellow. Secondary winding Ng turns Primary winding N, tums Magnetic Flux. Primary Secondary current current Primary votage Secondary valtage Transformer Core The ratio between the voltages at the secondary U, and the primary Up windings is equal to: U. b) U, N U а) U, N. U, , c) = 1 N, N U, P
Which of the following statements is true about an ideal transformer? O It changes the magnitude of DC signals. O It converts DC signals into AC signals. O It converts AC signals into DC signals. O It changes the magnitude of AC signals. hp
For the given circuit below, a step down transformer gives an RMS voltage of 230 V/ 10.2-0-10.2 V with a load resistance of 2.2 Kiloohms. Assume Silicon diodes are used. Determine the Peak Inverse Voltage of the diode. D. 23.23 28.85 17.57 14.43
A 25 kVA, 2 kV(rms)/100 V(rms) single phase transformer is connected between a 120 V(rms) utility supply and a resistive load. The load current was measured to be 20 A(rms). i. Determine the active power of the load. ii. Determine the primary RMS current. iii. Determine the equivalent resistance of the transformer as seen by the utility supply.