5/ B 3

Q: 5 400 200 A 1 120° 4 200 (mm) 350 B 2.

A: The number of I centres are given as : N=n(n-1)2N= Number of I centersn = number of links for…

Q: kinelic enorgy ol tro hoop it gium y: the hoop. Then, Cakulale the 1oling down without slipping an…

A: As per the guidelines we are subjected to solve only one question at a time please repost the same…

Q: 0.5 and For the system shown, the spring constant k = 400 kN/m, damping coefficient zeta = mass m =…

A:

Q: 1. All the following statements about beams are true, except? a. There are two equilibrium equations…

A: 1. Beams are generally subjected to transverse loads. Hence, (a) There are two equilibrium equations…

Q: A load P is supported by a structure consisting of rigid bar ABC, two identical solid bronze [E =…

A:

Q: create 2 fourbar designs that include the dimensions and angle of motion

A: It is asked to draw four bar mechanism with given motion

Q: 19. A tank containing saturated steam undergoes a rapid drop in pressure. This results in rainout…

A: In view of lumped mass and hotness balance conditions, he got mathematical outcomes for strain and…

Q: 1. Name the components marked withl, 2, 3, 4, 5, 6, 7, 8, 9, 10respectively. What function do the…

A: Given Hydraulic Circuit To find Name of the component Function of the component

Q: Prof. Dr. Necati Mahir esuzem Water -Boundary A piston-cylinder device initially contains 18 kg of…

A: Given Data m=18 kg P1=4 MPa T1=300°C W=2800 kJ P2=100 kPa

Q: Draw velocity polygon.

A: Solution:

Q: The bar AB slides so that its bottom point A has a velocity of 400 mm/s to the left along the…

A:

Q: 9. Please list the basic procedure of calculating the X- and Y-coordinates of the tool centerline…

A:

Q: 7. A SAE steel column has a circular cross-section of 16 mm in diameter and a length of 320 mm. The…

A:

Q: Estimate the flow rate Q of water discharging from the nozzle as shown in Figure 3. If the fluid…

A:

Q: A hollow bronze shaft of 75 mm outer diameter and 50 mm meter is slipped over a solid steel shaft 50…

A: Given: The outer diameter of bronze shaft, D = 75 mm = 0.075 m The diameter of steel shaft or inner…

Q: Q#2: the condenser of Geothermal Heat Pump will be cooled by A pipe with dimeter 3 cm buried in a…

A: The given information-   Diameter d= 3 cm = 0.03 m Cooling load Q = 8 ton = 8 ×3.516 = 28.128 kW hs…

Q: (a) Draw neat illustrative sketches to bring about the difference between a helical coil tension…

A: Helical spring -These types of springs are made of wire. These springs are supposed to carry load in…

Q: Please atleast answer this question. I will upvote

A: “Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for…

Q: What is the v-velocity at the centerline after refining the mesh

A: To explain: What is the v-velocity at the centerline after refining the mesh.

Q: Find the magnitude, direction and centre of pressure (point of application) of the resultant force…

A: Given:Side of triangular hatch, S=0.5 mPosition of top of triangular hatch from the free surface,…

Q: A circumferential fin of rectangular cross section, 3.7-cm OD and 0.3 cm thick, surrounds a 2.5-cm-…

A: GIVEN• A mild steel circumferential fin of a rectangular cross section on a tube.• Tube diameter…

Q: i) Kinematic Diagram Abtor

A: To determine the degree of freedom of the given kinematic diagram.

Q: the moment was clockwise so wy didnt you subtract it

A: This question is based on the concept of free body diagram and forces.

Q: the pressure and temperature at the end of the heat-addition process, (b) the net work output, (c)…

A: From the temperature, the relative specific volume and internal energy at inlet conditions can be…

Q: We begin with Direction A. (a) What is the x coordinate of the vector tail (x₁)? (b) What is the x…

A: “Since you have posted a question with multiple sub-parts, we will solve first three subparts for…

Q: 6. 0.05 kg of steam at 15 bar is contained in a rigid vessel of volume 0.0076 m³. What is the…

A:

Q: Given a 2.9 m and b=1.2 m determin the angle EAD Determine the angle EAD, %media:formula85.mml% O

A: The co-ordinates of the points from the given figure in vector for is as below.

Q: The piece of plastic is originally rectangular. Suppose that a = 330 mm and b = 420 mm .(Figure 1)…

A:

Q: Use Castigliano's theorem to determine the magnitude of deflection at midspan for the solid steel…

A: To Find : The deflection at the mid point shaft,Given : The dimensions are The distributed load is…

Q: At what temperature does water boil if P = 0.04 bar O a. 35.6 C O b. 81.6 C Oc. 85.94 C O d. 42.5 C…

A: