Answered: [5-7 Find the ratio of width 6 and…

[5-7 Find the ratio of width 6 and height h, which is a rectangular cross-section having the maximum section modulus from a circular cross-section with a diameter of 4 as shown in (Fig 5-311

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter9: Deflections Of Beams

Section: Chapter Questions

Problem 9.5.24P: A thin metal strip of total weight W and length L is placed across the top of a flat table of width...

See similar textbooks

Similar questions

A thin metal strip of total weight W and length L is placed across the top of a flat table of width L2as shown in the figure. What is the clearance S between the strip and the middle of the table? (The strip of metal has flexural rigidity EI.)
Solve the preceding problem for sx= 11 MPa and ??y= -20 MPa (see figure).
Determine the shape factor f for a cross section in the shape of a double trapezoid having the dimensions shown in the figure. Also, check your result for the special cases of a rhombus (b1= 0) and a rectangle (b1= b2).
3) For the given plate subjected to two point forces, calculate the nodal displacements and the moments at points A and B. (Note that A is the mid-point of the finite element) E = 30000 MPa h = 0.14 m v = 0.20 2 m 2 m 50 kN 2 m 50 kN A B 50 kN 50 kN 2 m 50 Cross-section along the symmetry axis
The system in the figure consists of AB copper bars with a diameter of 30 mm and BC aluminum bars with a diameter of 22 mm.The modulus of elasticity of copper is 110 GPa and that of aluminum is 75 GPa. Find the displacement of the point C with respect to the given.
L3 =440 B M1 IC M2 L4 = 510 M1= 81 M2-48 L3 (mm) L4 (mm) 80 mm 120 mm а-а -b-b Geometric situation in figure 4, which consists of small dimensions in figure 4 The system is made of steel structure and is under the influence of torsional moments. your rod angle AB 80mm; Angle BC is 120 mm and the sliding unit of the steel G= 80000 MPa. a- Draw the torsional moment diagram of the rod. b- Calculate the maximum shear stress that will develop in the system. C- Calculate the relative rotational value of point C with respect to point A.
In the figure, copper AB copper with a diameter of 24 mm and BC steel bars with a diameter of 20 mm are rigidly connected to each other at point B. A force of 6 kN was applied to the rod at the B point and 12 kN at the C point. Since the modulus of elasticity of copper is 100 GPa and the modulus of elasticity of steel is 200 GPa, find the displacement of the C point.
1. Three cubes of side l0, 2l0, and 3l0, are placed next to another (in contact) with their centers along a straight line and the l = 2l0 cube is in the middle (see Figure below).a) If the cubes are made of the same uniform material, find along this line the position of the center of mass of the system.b) We now replace the cube in the middle (l = 2l0) by another cube of the same volume but made of a different uniform material. What would be the mass density  of this cube compared to the mass density 0 of the initial cube if we want to locate the center of mass of the new system at the interface between the cube in the middle (l = 2l0) and the right-hand cube (l = 3l0)?
(Mechanics and Materials Class) Problem 33: Find the reactions at the supports, and find the shear force and bending moments.
A square plate with sides 1.5 m in length can rotate around an axle passing through its center of mass (CM) and perpendicular to its surface (see figure below). There are four forces acting on the plate at different points. The rotational inertia of the plate is 16 kg - m². Use the values given in the figure to answer the following questions. (Assume 0 = 40°. Express your answers in vector form.) 30.0 N 60.0 N CM 20.0 N 40.0 N (a) What is the net torque acting on the plate?
(Mechanics and Materials Class) Problem 59: Find the reactions at the supports, and find the shear force and bending moments.
For the composite object below (figure not to scale), the top triangle is made of titanium (density ~4540 kg/m³), the middle rectangle is made of stainless steel (density ~7700 kg/m³), and the bottom half-circle is made of tungsten (density ~19450 kg/m³). The object has a thickness of 5 mm, and the semiminor axis of the elliptical hole is 30 mm. (a) Find the center of gravity of the object. (b) Find the mass moment of inertia about an axis perpendicular to the page and passing through the center of gravity. 150 mm 150 mm" 500 mm 50 mm 200 mm 200 mm 75 mm 150 mm